Onkyo TX-8250 User Manual English etc - Page 31

> Before Start, > Part Names, > Install, > Initial Setup, > Playback

Get Onkyo TX-8250 PDF manuals and user guides View all Onkyo TX-8250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

> Before Start > Part Names > Install > Initial Setup > Playback Supplementary information | Advanced Setup | Others COAX2 OPT1 OPT2 "BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE", "PHONO": Allocate an input selector to the DIGITAL IN COAXIAL 2 jack. (Default Value is "CBL/SAT") "BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE", "PHONO": Allocate an input selector to the DIGITAL IN OPTICAL 1 jack. (Default Value is "GAME") "BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE", "PHONO": Allocate an input selector to the DIGITAL IN OPTICAL 2 jack. (Default Value is "TV/TAPE") 0 Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 20 bit, 24 bit, 176.4 kHz, 192 kHz/16 bit, 20 bit, 24 bit. 2. Main Volume Max Vol POn Vol HP Lvl Set the maximum value to avoid too high volume. Select "Off (default value)" or a value between "50" to "99". Set the volume level of when the power is turned on. Select "Last (default value)" (volume level before entering standby mode), "Min", "0.5" to "99.5" and "Max". 0 You cannot set a higher value than that of "Max Vol". Adjust the output level of the headphones. Select from "-12.0 dB" to "+12.0 dB". (Default Value is "0.0 dB") 3. Hardware SpImpedance Auto Stby NET Stby Set the impedance of the connected speakers. "4≠": When any of the connected speakers have 4 ≠ or more to less than 6 ≠ impedance, or when speaker systems are connected to both of the SPEAKERS A/B terminals "6≠ (default value)": When the connected speakers all have 6 ≠ or more impedance 0 Note that when connecting to both SPEAKERS A and B terminals, connect speakers with 8 ≠ to 16 ≠ impedance to both A and B. 0 For impedance, check the indications on the back of the speakers or their instruction manual. This setting places the unit on standby automatically after 20 minutes of inactivity without any audio input. (When "NET Stby" is on, this becomes the HYBRID STANDBY mode which reduces the increase in power consumption to a minimum.) "On": The unit will automatically enter standby mode. "AUTO STBY" lights on the display. "Off": The unit will not automatically enter standby mode. 0 "Auto Stby" is displayed on the display 30 seconds before the Auto Standby comes on. 0 Default values vary depending on the regions. When this feature is turned "On (default value)", you can turn on the power of the unit via the network using an application that can control this unit. 0 When using "NET Stby", power consumption increases even when this unit is on standby, however, the increase in power consumption is kept to a minimum by automatically entering the HYBRID STANDBY mode, where only essential circuits are operating. 0 When the connection to the network is lost, "NET Stby" is disabled to reduce power consumption. Use the power button on the remote controller or main unit to turn the unit on if this happens. En 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
Supplementary information
|
Advanced Setup
| Others
31
En
0
Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32 kHz,
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 20 bit, 24 bit, 176.4 kHz, 192 kHz/16 bit,
20 bit, 24 bit.
2. Main Volume
3. Hardware
COAX2
"BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE",
"PHONO": Allocate an input selector to the DIGITAL IN
COAXIAL 2 jack. (Default Value is "CBL/SAT")
OPT1
"BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE",
"PHONO": Allocate an input selector to the DIGITAL IN
OPTICAL 1 jack. (Default Value is "GAME")
OPT2
"BD/DVD", "CBL/SAT", "GAME", "PC", "CD", "TV/TAPE",
"PHONO": Allocate an input selector to the DIGITAL IN
OPTICAL 2 jack. (Default Value is "TV/TAPE")
Max Vol
Set the maximum value to avoid too high volume. Select "Off
(default value)" or a value between "50" to "99".
POn Vol
Set the volume level of when the power is turned on. Select
"Last (default value)" (volume level before entering standby
mode), "Min", "0.5" to "99.5" and "Max".
0
You cannot set a higher value than that of "Max Vol".
HP Lvl
Adjust the output level of the headphones. Select from
"-12.0 dB" to "+12.0 dB". (Default Value is "0.0 dB")
SpImpedance
Set the impedance of the connected speakers.
"4
≠
": When any of the connected speakers have 4
≠
or more to
less than 6
≠
impedance, or when speaker systems are
connected to both of the SPEAKERS A/B terminals
"6
≠
(default value)": When the connected speakers all have 6
≠
or more impedance
0
Note that when connecting to both SPEAKERS A and B
terminals, connect speakers with 8
≠
to 16
≠
impedance to
both A and B.
0
For impedance, check the indications on the back of the
speakers or their instruction manual.
Auto Stby
This setting places the unit on standby automatically after 20
minutes of inactivity without any audio input. (When "NET Stby"
is on, this becomes the HYBRID STANDBY mode which reduces
the increase in power consumption to a minimum.)
"On": The unit will automatically enter standby mode. "AUTO
STBY" lights on the display.
"Off": The unit will not automatically enter standby mode.
0
"Auto Stby" is displayed on the display 30 seconds before the
Auto Standby comes on.
0
Default values vary depending on the regions.
NET Stby
When this feature is turned "On (default value)", you can turn on
the power of the unit via the network using an application that
can control this unit.
0
When using "NET Stby", power consumption increases even
when this unit is on standby, however, the increase in power
consumption is kept to a minimum by automatically entering
the HYBRID STANDBY mode, where only essential circuits
are operating.
0
When the connection to the network is lost, "NET Stby" is
disabled to reduce power consumption. Use the power button
on the remote controller or main unit to turn the unit on if this
happens.