Onkyo TX-NR3008 Owner Manual - Page 114
Go to Hardware Setup menu., Select Via USB and press
View all Onkyo TX-NR3008 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 114 highlights
6 Select the USB input source. "Now Initializing" is displayed on the front display and then the name of the USB storage device is displayed. It will take 20 to 30 seconds to recognize the USB storage device. 7 Press RECEIVER followed by SETUP on the remote controller. Main menu will be displayed on TV screen. Procedures thereafter can also be performed on the AV receiver by using its SETUP, arrow, and ENTER buttons. 8 Go to "Hardware Setup" menu. 9 Go to "Firmware Update" menu. 10 Select "Via USB" and press ENTER. 11 Select "Update" and press ENTER. Updating will begin. As the updating progresses, the TV screen may disappear depending on the program updated. In this case, you can see the update progress on the front display of the AV receiver. The TV screen will reappear when you finish the update and turn on the AV receiver. Do not turn off the AV receiver and do not remove the USB storage device during updating process. 12 Message "Complete!" appears on the front display of the AV receiver, indicating that the update has been completed. 13 Using ON/STANDBY on the front panel, turn off the AV receiver and then remove the USB storage device. * Do not use ON or STANDBY on the remote controller. 14 Press ON/STANDBY to turn on the AV receiver. Congratulations!! Now you have the latest firmware on your Onkyo AV receiver. Troubleshooting Case1: If "No Update" is displayed on the front display of the AV receiver, the firmware has already been updated. You do not need to do anything further. Case2: If an error occurs, "Error!! *-** No media" is displayed on the front display of the AV receiver. (Alpha-numeric characters on the front display are denoted by asterisks.) See the following table and take appropriate action. ■ Errors during update via USB Error Code *-10, *-20 *-14 Others Description USB storage device is not detected. Make sure the USB flash memory or USB cable is properly connected to the USB port. If the USB storage device has its own power supply, use it to power the USB storage device. An update file is not found in the root folder of the USB storage device, or an update file is for other model. Retry download following instructions at the support website. If the error persists, please contact Onkyo Support and provide the error code. Retry the update procedure from the beginning. If the error persists, please contact Onkyo Support and provide the error code. Case3: If an error occurs during the update, disconnect then reconnect the AC power cord and try again. Case4: If Error Code 3-51 is displayed, try the following procedure. 1. Disconnect the AC power cord then reconnect. 2. Start up this device, and select the NET/USB selector. 3. After the "Now Initializing" display has changed, perform the update again. Case5: If an error has occurred due to wrong selection of input sources, turn off and on the AV receiver. Then retry the update. ONKYO CORPORATION 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN The Americas ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET Europe ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 China, Hong Kong ONKYO CHINA LIMITED Unit 1&12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung, N.T., Hong Kong Tel: 852-2429-3118 Fax: 852-2428-9039 Asia, Oceania, Middle East, Africa Please contact an ONKYO distributor referring to Onkyo SUPPORT site. En 114