Onkyo TX-NR3008 Owner Manual - Page 53
Level Calibration, Equalizer Settings, Dynamic Volume
View all Onkyo TX-NR3008 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 53 highlights
■ Left, Front Wide Left, Front High Left, Center, Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer 1, Subwoofer 2*1 `Specify the distance from the each speaker to your listening position. Note • Speakers that you set to "No" or "None" in the "Speaker Configuration" cannot be selected (➔ 51). • Speakers B cannot be selected if "Speakers Type(Front B)" is set to "Not Use" (➔ 51). *1 If the "Subwoofer" setting is set to "1ch", this setting cannot be selected (➔ 51). Level Calibration This setting is set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup function (➔ 32). For Speakers B, you need to change the settings manually. Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. The other speakers (i.e., subwoofer, center, surround, and surround back) use the same level settings for Speakers A and Speakers B. ■ Left, Front Wide Left, Front High Left, Center*1, Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left `-12.0dB to 0.0dB to +12.0dB in 0.5 dB step. ■ Subwoofer 1*1, Subwoofer 2*1*2 `-15.0dB to 0.0dB to +12.0dB in 0.5 dB step. Note • Speakers that you set to "No" or "None" in the "Speaker Configuration" cannot be selected (➔ 51). • The speakers cannot be calibrated while the AV receiver is muted. • The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder. • Speakers B cannot be selected if "Speakers Type(Front B)" is set to "Not Use". • The "Level Calibration" setting cannot be selected if "Audio TV Out" setting is set to "On". *1 For the center speaker and subwoofer, the level settings made by using the Home menu are saved (➔ 30). *2 If the "Subwoofer" setting is set to "1ch", this setting cannot be selected (➔ 51). Tip • If you're using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading. Equalizer Settings This setting is set automatically by Audyssey MultEQ XT32 Room Correction and Speaker Setup function (➔ 32). With the Equalizer settings, you can adjust the tone of speakers individually with a 7-band equalizer. The volume of each speaker can be set (➔ 53). The Equalizer settings only apply to Speakers A and cannot be adjusted while Speakers B is selected. ■ Equalizer ` Manual: You can adjust the equalizer for each speaker manually. If you selected "Manual", continue with this procedure. 1 Press X to select "Channel", and then use F/ S to select a speaker. 2 Use R/X to select a frequency, and then use the F/S to adjust the level at that frequency. The volume at each frequency can be adjusted from -6dB to 0dB to +6dB in 1 dB steps. Note • You can select: "63Hz", "160Hz", "400Hz", "1000Hz", "2500Hz", "6300Hz", or "16000Hz". And for the subwoofer, "25Hz", "40Hz", "63Hz", "100Hz", or "160Hz". • While the Direct or Pure Audio listening mode is selected, the equalizer settings have no effect. Tip • Low frequencies (e.g., 63Hz) affect bass sounds; high frequencies (e.g., 16000Hz) affect treble sounds. 3 Use R to select "Channel", and then use F/S to select another speaker. Repeat steps 1 and 2 for each speaker. You cannot select speakers that you set to "No" or "None" in the "Speaker Configuration" (➔ 51). ` Audyssey: This is selected automatically by Audyssey MultEQ XT32 Room Correction and Speaker Setup function. The Audyssey indicator will light (➔ 9) and "Dynamic EQ" and "Dynamic Volume" become available (➔ 57). When "Audyssey" is selected, "Dolby Volume" becomes "Off" automatically (➔ 55). ` Off: Tone off, response flat. En 53