Onkyo TX-RZ730 Owners Manual - English - Page 132

Crossover

Get Onkyo TX-RZ730 PDF manuals and user guides View all Onkyo TX-RZ730 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Bi-Amp Speaker Impedance Default Value No 6ohms Setting Details Set whether the front speakers are bi-amp connected. "No": When front speakers are not bi-amp connected "Yes": When front speakers are bi-amp connected • This setting will be set to "No" in either of following cases. -- When 2 sets of height speakers are used -- When surround back speakers and height speakers are being used at the same time. -- When "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone 3" Set the impedance (Ω) of the connected speakers. "4ohms": When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance "6ohms": When the connected speakers all have 6 Ω or more impedance • For impedance, check the indications on the back of the speakers or their instruction manual. „„2. Crossover Change the settings of crossover frequencies. • As for the THX-certified speakers, the following settings are recommended. -- Crossover frequency → "80Hz(THX)" -- "LPF of LFE" → "80Hz" -- "Double Bass" → "Off" Setting Item Front Default Value 80Hz(THX) Setting Details Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers. Refer to the instruction manual of your speakers to make the setting. Setting Item Center Height 1 Height 2 Default Value 80Hz(THX) 80Hz(THX) 80Hz(THX) Setting Details Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. 132 Front Panel≫ Rear Panel≫ Remote≫

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
132
Front Panel
≫
Rear Panel
≫
Remote
≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
Setting Item
Default Value
Setting Details
Bi-Amp
No
Set whether the front speakers are bi-amp
connected.
"No": When front speakers are not bi-amp
connected
"Yes": When front speakers are bi-amp connected
• This setting will be set to "No" in either of
following cases.
–
When 2 sets of height speakers are used
–
When surround back speakers and height
speakers are being used at the same time.
–
When "Zone Speaker" is set to "Zone 2" or
"Zone 2/Zone 3"
Speaker
Impedance
6ohms
Set the impedance (Ω) of the connected speakers.
"4ohms": When any of the connected speakers
have 4 Ω or more to less than 6 Ω impedance
"6ohms": When the connected speakers all have
6 Ω or more impedance
• For impedance, check the indications on the
back of the speakers or their instruction manual.
±
2. Crossover
Change the settings of crossover frequencies.
•
As for the THX-certified speakers, the following settings are recommended.
–
Crossover frequency → "80Hz(THX)"
–
"LPF of LFE" → "80Hz"
–
"Double Bass" → "Off"
Setting Item
Default Value
Setting Details
Front
80Hz(THX)
Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
If "Configuration" - "Subwoofer" is set to "No",
"Front" is fixed to "Full Band", and the low
pitched range of the other channels is output
from the front speakers. Refer to the instruction
manual of your speakers to make the setting.
Setting Item
Default Value
Setting Details
Center
80Hz(THX)
Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.
Height 1
80Hz(THX)
Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.
Height 2
80Hz(THX)
Select the crossover frequency from "40Hz" to
"200Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.