Onkyo TX-SR383 Owners Manual - English - Page 45

Tuning Manually, Improving FM reception, Frequency step setting Australian models

Get Onkyo TX-SR383 PDF manuals and user guides View all Onkyo TX-SR383 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Contents ≫ Preparation ≫ Playback ≫ Setup ≫ Tuning Manually 1. Press TUNER to switch to "TUNER" input. 2. Press BAND repeatedly to select either "AM" or "FM ST". 3. Press TUNING +/- to select the desired radio station. • Each time you press TUNING +/-, the frequency changes by 1 step. If the button is held down, the frequency changes continuously. Improving FM reception When FM broadcasts reception is poor, set the receiver to the mono reception mode. 1. Press BAND to select "FM MONO". Frequency step setting (Australian models) If you find that you can't tune into stations successfully, the frequency step may not be suitable for your country/region. In such a case, select a frequency step suitable for your region. 1. Set the unit to standby mode. 2. While pressing and holding the TUNING button of the main unit, press the ON/STANDBY button to turn the unit on. Each time you operate, the setting is switched between "9 kHz/0.05 MHz" and "10 kHz/0.1 MHz". • Default: 9 kHz/0.05 MHz • This operation is not possible if "Control" and "Standby Through" are set to other than "OFF". ❏❏Presetting a Radio Station ( p46) 45 Front Panel≫ Rear Panel≫ Remote≫

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
45
Front Panel
≫
Rear Panel
≫
Remote
≫
Contents
≫
Preparation
≫
Playback
≫
Setup
≫
Tuning Manually
1. Press TUNER to switch to "TUNER" input.
2. Press BAND repeatedly to select either "AM" or "FM ST".
3. Press TUNING +/– to select the desired radio station.
• Each time you press TUNING +/–, the frequency changes by 1 step. If the
button is held down, the frequency changes continuously.
Improving FM reception
When FM broadcasts reception is poor, set the receiver to the mono reception
mode.
1. Press BAND to select "FM MONO".
Frequency step setting (Australian models)
If you find that you can't tune into stations successfully, the frequency step may
not be suitable for your country/region. In such a case, select a frequency step
suitable for your region.
1. Set the unit to standby mode.
2. While pressing and holding the
TUNING button of the main unit, press the
ON/STANDBY button to turn the unit on. Each time you operate, the setting is
switched between "9 kHz/0.05 MHz" and "10 kHz/0.1 MHz".
• Default: 9 kHz/0.05 MHz
• This operation is not possible if "Control" and "Standby Through" are set to
other than "OFF".
❏
Presetting a Radio Station (
p46
)