Optoma 4K500 4K500 User Manual - Page 55

Warning indicators, Other problems, Remote control problems, LED lightning messages

Get Optoma 4K500 PDF manuals and user guides View all Optoma 4K500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

ADDITIONAL INFORMATION Other problems T he projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. L amp burns out or makes a popping sound ‡‡ When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 45-46. Remote control problems If the remote control does not work ‡‡ Check the operating angle of the remote control is pointed within ±15° to the IR receiver on the projector. ‡‡ Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (23 ft) of the projector. ‡‡ Make sure batteries are inserted correctly. ‡‡ Replace batteries if they are exhausted. Warning indicators When the warning indicators (see below) light up or flash, the projector will automatically shutdown: ‡‡ "LAMP" LED indicator is lit red and if "On/Standby" indicator flashes red. ‡‡ "TEMP" LED indicator is lit red and if "On/Standby" indicator flashes red. This indicates the projector has overheated. Under normal conditions, the project can be switched back on. ‡‡ "TEMP" LED indicator flashes red and if "On/Standby" indicator flashes red. Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or flash, please contact your nearest service center for assistance. LED lightning messages Message Standby state (Input power cord) Power on (Warming) Power on and Lamp lighting Power off (Cooling) Error (Over temp.) Error (Fan failure) Error (Lamp failure) Power LED (Red) Steady light Flashing Flashing Flashing Power LED (Blue) TEMP-LED (Red) Flashing (0.5 sec off / 0.5 sec on) Steady light Flashing (0.5 sec off / 0.5 sec light). Back to red steady light when cooling fan turns off. Steady light Flashing LAMP-LED (Red) Steady light English 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
English
55
ADDITIONAL INFORMATION
Other problems
The projector stops responding to all controls
±
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
±
When the lamp reaches its end of life, it will burn out and may make a loud popping sound.
If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages
45-46
.
Remote control problems
If the remote control does not work
±
Check the operating angle of the remote control is pointed within ²15° to the IR receiver on the
projector.
±
Make sure there are not any obstructions between the remote control and the projector. Move to within
7 m (23 ft) of the projector.
±
Make sure batteries are inserted correctly.
±
Replace batteries if they are exhausted.
Warning indicators
When the warning indicators (see below) light up or flash, the projector will automatically shutdown:
±
"LAMP" LED indicator is lit red and if "On/Standby" indicator flashes red.
±
"TEMP" LED indicator is lit red and if "On/Standby" indicator flashes red. This indicates the projector
has overheated. Under normal conditions, the project can be switched back on.
±
"TEMP" LED indicator flashes red and if "On/Standby" indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
flash, please contact your nearest service center for assistance.
LED lightning messages
Message
Power LED
Power LED
TEMP-LED
LAMP-LED
(Red)
(Blue)
(Red)
(Red)
Standby state
(Input power cord)
Steady light
Power on (Warming)
Flashing
(0.5 sec off /
0.5 sec on)
Power on and Lamp
lighting
Steady light
Power off (Cooling)
Flashing
(0.5 sec off /
0.5 sec light). Back
to red steady light
when cooling fan
turns off.
Error (Over temp.)
Flashing
Steady light
Error (Fan failure)
Flashing
Flashing
Error (Lamp failure)
Flashing
Steady light