Optoma HD80 User Manual - Page 41

Replacing the lamp - bulb

Get Optoma HD80 PDF manuals and user guides
UPC - 796435216283
View all Optoma HD80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

English Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. Warning: Lamp com- When you see this message, please contact your local reseller or partment is hot! Allow service center to change the lamp as soon as possible. Make sure it to cool down before changing lamp! the projector has been cooled down for at least 30 minutes before changing the lamp. 1 3 2 4 Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power button. 2. Allow the projector to cool down at least 30 minutes. 3. Disconnect the power cord. 4. Use a screwdriver to remove the screw from the cover. 5. Push up and remove the cover. 6. Remove the 2 screws from the lamp module. 7. Pull out the lamp module.  To replace the lamp module, reverse the previous steps. 8. Turn on the projector and do "Lamp Reset" after the lamp module is replaced. Lamp Reset: (i)Press "Menu" -> (ii)Select "System" -> (iii)Select "Lamp setting" ->(iv)Select "Lamp reset" -> (v)Select "Yes". 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
English
41
Appendices
Replacing the lamp
The projector automatically detects the lamp life.
When the lamp
life is nearing the end of use, you will receive a warning message.
When you see this message, please contact your local reseller or
service center to change the lamp as soon as possible. Make sure
the projector has been cooled down for at least 30 minutes before
changing the lamp.
Warning: Lamp com-
partment is hot!
Allow
it to cool down before
changing lamp!
Warning: To reduce the
risk of personal injury,
do not drop the lamp
module or touch the
lamp bulb. The bulb
may shatter and cause
injury if it is dropped.
3
2
4
Lamp Replacing Procedure:
1.
Switch off the power to the projector by pressing the Power
button.
2.
Allow the projector to cool down at least 30 minutes.
3.
Disconnect the power cord.
4.
Use a screwdriver to remove the screw from the cover.
5.
Push up and remove the cover.
6.
Remove the 2 screws from the lamp module.
7.
Pull out the lamp module.
To replace the lamp module, reverse the previous steps.
8.
Turn on the projector and do “Lamp Reset” after the lamp
module is replaced.
Lamp Reset: (i)Press “Menu” -> (ii)Select “System” ->
(iii)Select “Lamp setting” ->(iv)Select “Lamp reset” ->
(v)Select “Yes”.
1