Optoma HD83 User's Manual - Page 18

Powering off the projector, Warning Indicator - fan failure

Get Optoma HD83 PDF manuals and user guides View all Optoma HD83 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Installation Powering off the projector 1. Press the " " button on the remote control or " " button on the side of the projector two times with one second interval to turn off the projector. First time to push the button will display the following message on the screen. NOTE  Contact the nearest service center if the projector displays these symptoms. Press the " " button again to confirm the shut down. If the button is not pressed, the message will disappear after 15 seconds. 2. The cooling fans continue to operate for about 60 seconds for cooling cycle and the Power LED will turn blue and flashing. When the lights solid red, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press " " button to restart the projector. 3. Disconnect the power cord from the electrical outlet and from the projector. 4. Do not turn on the projector immediately following the power off procedure. Warning Indicator  When the "LAMP" indicator is lit orange, the projector will shut down automatically. Please call the nearest Optoma facility for assistance.  When the "TEMP" indicator turns red, it indicates the projector has overheated. The projector will shut down automatically. Under normal conditions, the projector can be switched on again after it has cooled down.  When the "TEMP" indicator flashes red, it indicates the fan has failed.  After the projector has cooled down, you can press and hold " " button on the remote control for 10 seconds to leave failure mode to standby mode. English 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
English
±8
Installation
Powering Off the Projector
±. Press the
“
”
button on the remote control or
“
” button on the
side of the projector two times with one second interval
to turn off
the projector. First time to push the button will display the follow-
ing message on the screen.
Press the
“
”
button again to confirm the shut down. If the button
is not pressed, the message will disappear after ±5 seconds.
2. The cooling fans continue to operate for about 60 seconds for
cooling cycle and the Power LED will turn blue and flashing. When
the lights solid red, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until
the projector has completed the cooling cycle and has entered
standby mode. Once in standby mode, simply press
“
”
button to
restart the projector.
3. Disconnect the power cord from the electrical outlet and from the
projector.
4. Do not turn on the projector immediately following the power off
procedure.
Warning Indicator
When the “LAMP” indicator is lit orange, the projector will shut
down automatically. Please call the nearest Optoma facility for
assistance.
When the “TEMP” indicator turns red, it indicates the projector has
overheated. The projector will shut down automatically.
Under normal conditions, the projector can be switched on again
after it has cooled down.
When the “TEMP” indicator flashes red, it indicates the fan has
failed.
After the projector has cooled down, you can press and hold “
”
button on the remote control for ±0 seconds to leave failure mode
to standby mode.
Contact the near-
est service center
if the projector
displays these
symptoms.
N
OTE