Optoma UHZ65LV UHZ65LV UM - Page 22

Powering on / off the projector

Get Optoma UHZ65LV PDF manuals and user guides View all Optoma UHZ65LV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

USING THE PROJECTOR Powering on / off the projector or On Off Geometric Correction PIP/PBP F1 Mode F2 AV Mute ENTER On Off Info. Source Geometric Correction PIP/PBP F1 Mode F2 AV Mute Re-Sync F3 ENTER Volume Info. Source Volume D Zoom Re-Sync F3 D Zoom Lens cap Menu Menu Format Freeze Format Freeze Remote ID All VGA S-Video HDMI1 HDMI2 123 HDBaseT Video DVI HDMI3 456 Remote BNC YPbPr DisplayPort 3D 7890 ID All VGA S-Video HDMI1 HDMI2 Powering on 1. Remove the lens cap. 123 HDBaseT Video DVI HDMI3 456 BNC YPbPr DisplayPort 3D 2. Securely connect the power lead and signal/source cable. W7 hen8 con9 nec0ted, the Power LED will turn red. 3. Turn on the projector by pressing the button on the projector keypad or remote control. 4. A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue. Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection orientation, and other settings. Powering off 1. Turn off the projector by pressing the button on the projector keypad or the control. 2. The following message will be displayed: Power Off button on the remote Press power key again. 3. Press the or button again to confirm, otherwise the message will disappear after 15 seconds. When you press the or button for the second time, the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the Power LED will flash blue. When the Power turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure. 22 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
English
22
USING THE PROJECTOR
Powering on / off the projector
F3
On
Geometric
Mode
Correction
PIP/PBP
Off
F1
F2
AV Mute
ENTER
Source
Volume
D Zoom
Info.
VGA
1
S-Video
2
HDMI1
3
HDMI2
HDMI3
Format
Freeze
Remote
ID
All
HDBaseT
4
Video
5
DVI
6
BNC
7
YPbPr
8
DisplayPort
9
3D
0
Re-Sync
Menu
F3
or
Lens cap
On
Geometric
Correction
PIP/PBP
Off
F1
F2
Powering on
1.
Remove the lens cap.
2.
Securely connect the power lead and signal/source cable. When connected, the Power LED will turn
red.
3.
Turn on the projector by pressing the
button on the projector keypad or remote control.
4.
A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue.
Note:
The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the
button on the projector keypad or the
button on the remote
control.
2.
The following message will be displayed:
Power Off
Press power key again.
3.
Press the
or
button again to confirm, otherwise the message will disappear after 15 seconds.
When you press the
or
button for the second time, the projector will shut down.
4.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the Power
LED will flash blue. When the Power turns solid red, this indicates the projector has entered standby
mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and
the projector has entered standby mode. When the projector is in standby mode, simply press the
button again to turn on the projector.
5.
Disconnect the power lead from the electrical outlet and the projector.
Note:
It is not recommended that the projector is turned on immediately, right after a power off procedure.