Optoma UHZ65LV UHZ65LV UM - Page 64

Warning indicators, LED lightning messages

Get Optoma UHZ65LV PDF manuals and user guides View all Optoma UHZ65LV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

ADDITIONAL INFORMATION Warning indicators When the warning indicators (see below) light up or flash, the projector will automatically shutdown: ‡‡ "Laser" LED indicator is lit red and if "Power" indicator flashes red. ‡‡ "Temp" LED indicator is lit red and if "Power" indicator flashes red. This indicates the projector has overheated. Under normal conditions, the project can be switched back on. ‡‡ "Temp" LED indicator flashes red and if "Power" indicator flashes red. Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or flash, please contact your nearest service center for assistance. LED lightning messages Message Standby state (Input power cord) Power on (Warming) Power on and Laser lighting Power off (Cooling) Error (Laser failure) Error (Fan failure) Error (Over temp.) Standby State (Burn in mode) Burn-in (Warming) (*) Burn-in (Cooling) (*) Burn in (Laser lighting) (*) Burn in (Laser off) (*) Power LED (Red) (Blue) Steady light Flashing Flashing Flashing Flashing (0.5 sec off / 0.5 sec on) Steady light Flashing (0.5 sec off / 0.5 sec on). Back to red steady light when cooling fan turns off. Flashing Flashing Flashing Flashing (3 sec on / 1 sec off) Flashing (1 sec on / 3 sec off) Temp LED (Red) Flashing Steady light Laser LED (Red) Steady light Note: ‡‡ (*)If power is less than 0.5W and the power LED is red, change the power LED to flashing red. a) Turn all LEDs off after the OSD menu disappears. b) Power LED on: No signal; OSD disappears. c) Power LED off: Signal is detected; OSD disappears. 64 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
English
64
ADDITIONAL INFORMATION
Warning indicators
When the warning indicators (see below) light up or flash, the projector will automatically shutdown:
±
“Laser” LED indicator is lit red and if “Power” indicator flashes red.
±
“Temp” LED indicator is lit red and if “Power” indicator flashes red. This indicates the projector has
overheated. Under normal conditions, the project can be switched back on.
±
“Temp” LED indicator flashes red and if “Power” indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
flash, please contact your nearest service center for assistance.
LED lightning messages
Message
Power LED
Temp LED
Laser LED
(Red)
(Blue)
(Red)
(Red)
Standby state
(Input power cord)
Steady light
Power on (Warming)
Flashing
(0.5 sec off / 0.5 sec
on)
Power on and Laser lighting
Steady light
Power off (Cooling)
Flashing
(0.5 sec off / 0.5
sec on). Back to red
steady light when
cooling fan turns off.
Error (Laser failure)
Flashing
Steady light
Error (Fan failure)
Flashing
Flashing
Error (Over temp.)
Flashing
Steady light
Standby State (Burn in
mode)
Flashing
Burn-in (Warming) (*)
Flashing
Burn-in (Cooling) (*)
Flashing
Burn in (Laser lighting) (*)
Flashing
(3 sec on / 1 sec off)
Burn in (Laser off) (*)
Flashing
(1 sec on / 3 sec off)
Note:
±
(*)If power is less than 0.5W and the power LED is red, change the power LED to flashing red.
a)
Turn all LEDs off after the OSD menu disappears.
b)
Power LED on: No signal; OSD disappears.
c)
Power LED off: Signal is detected; OSD disappears.