Optoma WHD200 User Manual - Page 23

or/and

Get Optoma WHD200 PDF manuals and user guides View all Optoma WHD200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Poor picture quality or intermittent video. your AV source devices. * Ensure your source devices connected to the WHD200 transmitter are powered on. * Ensure the proper cables are connected between the receiver and your 2nd HDTV near the receiver.  Check if your video resolution with HDMI input from your device is either 1080p, 1080i, 720p, 576p, or 480p. Please refer to the "Supported Resolution" chapter where the video frame rate from your HD AV device WHD200 can support is defined.  Ensure the transmission distance is less than 66 feet (LOS). No audio. IR Blaster can't control Source device.  Check your TV's volume is properly set and not set in "MUTE" mode.  Check if your source player's audio volume has been turned up..  Ensure the bit rate of audio from the source device can be supported by WHD200. Please refer to the details in Chapter 6, Audio Bit Rate Support.  Check where is IR sensor of Source device. Make sure IR Blaster sensor is close and straight to Source device's IR sensor. Please refer Chapter 3, step 3 for reference setup. Change IR Blaster frequency to meet Source device's requirement. See the page 20 for the IR blaster frequency switch. No 3D video output OSD displayed : TX or/and RX * Check both of TVs (include Tx and Rx side) should support 3D video format. Either one of TV only support 2D format, then 3D output might not supported. * If user wants to display 3D video on HDTV which supported 3D video, please turn off 2D HDTV and RE-power on 3D HDTV. Then set the source player to 3D video format output for the 3D display. * Check the video output setting of Source player (ex. Blu-ray Disc, PS3..etc.). If the video output setting of Source player is 3D video format, It might be abnormal display on HDTV which not supports 3D format. * 3D video format do not support on current equipments status. If user wants to display 3D video on HDTV which supported 3D video, please turn off 2D HDTV and RE-power on 3D HDTV. Then set the source player to 3D video format output for the 3D display. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
23
your AV source devices.
* Ensure your source devices connected to the WHD200 transmitter
are powered on.
* Ensure the proper cables are connected between the receiver and
your 2
nd
HDTV near the receiver.
Poor picture quality or
intermittent video.
Check if your video resolution with HDMI input from your device is
either 1080p, 1080i, 720p, 576p, or 480p. Please refer to the
“Supported Resolution” chapter where the video frame rate from
your HD AV device WHD200 can support is defined.
Ensure the transmission distance is less than 66 feet (LOS).
No audio.
Check your TV’s volume is properly set and not set in "MUTE" mode.
Check if your source player’s audio volume has been turned up..
Ensure the bit rate of audio from the source device can be supported
by WHD200. Please refer to the details in Chapter 6, Audio Bit Rate
Support.
IR Blaster can’t control
Source device.
Check where is IR sensor of Source device. Make sure IR Blaster
sensor is close and straight to Source device’s IR sensor. Please refer
Chapter 3, step 3 for reference setup.
Change IR Blaster frequency to meet Source device’s requirement.
See the page 20 for the IR blaster frequency switch.
No 3D video output
OSD displayed :
TX
or/and
RX
* Check both of TVs (include Tx and Rx side) should support 3D video
format. Either one of TV only support 2D format, then 3D output might
not supported.
* If user wants to display 3D video on HDTV which supported 3D video,
please turn off 2D HDTV and RE-power on 3D HDTV. Then set the
source player to 3D video format output for the 3D display.
* Check the video output setting of Source player (ex. Blu-ray Disc,
PS3..etc.). If the video output setting of Source player is 3D video
format, It might be abnormal display on HDTV which not supports 3D
format.
* 3D video format do not support on current equipments status. If user
wants to display 3D video on HDTV which supported 3D video, please
turn off 2D HDTV and RE-power on 3D HDTV. Then set the source
player to 3D video format output for the 3D display.