Panasonic AW-HE42 Operating Instructions 1 - Page 64
G/L IN connector [G/L IN], Service switches, Notes, Service switch settings
View all Panasonic AW-HE42 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 64 highlights
Operating Instructions Parts and their functions (continued) vG/L IN connector [G/L IN] This is the external sync signal input connector. This unit supports BBS (Black Burst Sync) and tri-level synchronization. External synchronization (genlock) can be applied to achieve phase alignment when multiple cameras are to be used or when the unit is to be used in combination with other devices. Supply to this connector the sync signals that correspond to the video signal format which has been set. Format External sync signal input format BBS Tri-level sync 1080/59.94p 1080/29.97p 1080/59.94i 1080/29.97PsF 720/59.94p 480/59.94i 480/59.94i 480/59.94i 480/59.94i 480/59.94i 1080/59.94i - 1080/59.94i 1080/59.94i 720/59.94p 1080/50p 1080/25p 1080/50i 1080/25PsF 720/50p 576/50i 576/50i 576/50i 576/50i 576/50i 1080/50i - 1080/50i 1080/50i 720/50p ●● External synchronization is performed using the SDI video signal. Synchronization is not possible using the HDMI video signal or the IP video signal. For horizontal phase adjustment, refer to the Operating Instructions (PDF) → "Camera menu items" → "Genlock screen". wService switches SW1 SW2 SW3 SW4 ON OFF SW5 SW6 SW7 SW8 Function OFF ON Factory setting SW1 Camera SW2 address setting (standard serial See descriptions for SW1 to SW3 SW3 communication) OFF OFF OFF Panasonic SW4 Communication format proprietary serial Standard serial communication communication OFF SW5 Always leave at OFF (used for factory adjustments) OFF SW6 Infrared output Disable Enable OFF SW7 Communication baud rate 9600 bps 38400 bps OFF SW8 Communication connector RS-422 RS-232C OFF Notes ●● Perform switch settings before turning the unit on. ●● Cameras whose camera address setting switches are set to AUTO cannot coexist with cameras whose switches are set to 1 to 7. ●● Manually setting multiple cameras to the same address will not allow you to control multiple cameras from a single controller simultaneously. Service switch settings (1) SW1 to SW3: Camera address setting switches Configure the camera address. Set this to AUTO under normal circumstances. When cameras are set to AUTO, addresses will be assigned to the cameras automatically in response operation from the controller in the order in which the cameras were connected. To manually configure the address, set the switches as follows. Address SW1 SW2 SW3 AUTO 1 2 3 4 5 6 7 OFF ON OFF ON OFF ON OFF ON OFF ON ON OFF OFF ON ON OFF OFF ON ON ON ON OFF OFF OFF (2) SW4: Communication format selection switch Selects the communication format. When this is set to ON, standard serial communication is enabled. When this is set to OFF, Panasonic's proprietary serial communication is enabled. (3) SW5: Maintenance switch Fixed at OFF. Do not change this switch setting. (4) SW6: Infrared output switch When this is set to ON, infrared output is enabled. The signal received via the remote control sensor is output from pins 7 and 8 of the RS-232C IN connector. Signal output is disabled when this is set to OFF. (5) SW7: Communication baud rate switch When this is set to ON, the baud rate is 38400 bps. When this is set to OFF, the baud rate is 9600 bps. (6) SW8: Communication connector switch When this is set to ON, RS-232C is enabled. When this is set to OFF, RS-422 is enabled. 64