Panasonic BB-HCM735A Installation Guide - Page 2

Camera Diagram Front View A Lens cover A B Lens C Microphone B D Indicator*1 C D Side and Bottom View E FACTORY DEFAULT E RESET button F F SD memory card slot G RESTART button G H FUNCTION button/indicator H I Stand/tripod mounting I hole Rear View J K L M N OPQRS *1 See 1.1 Understanding the Camera Indicator in the Troubleshooting Guide on the CD-ROM for indicator meaning. J Stand mounting hole K Serial number and MAC address label L AC adaptor cord/video cable hook M Speaker/microphone cable hook N LAN port O DC IN P External I/O interface Q VIDEO OUT terminal R AUDIO OUT terminal S MIC terminal Connections Before proceeding, confirm that your PC is connected to your router and can access the Internet. Also confirm that your router's UPnP™ feature is enabled. (Most routers have UPnP™ turned off by default.) Refer to the operating instructions included with your router or to the Panasonic Network Camera website (http://panasonic.net/pcc/ipcam/) for more information. When connecting the camera using PoE (Power over Ethernet) Connect the camera to your PoE hub using a LAN cable (Cat-5 straight cable) as described below. 1. Connect a LAN cable to the camera and to the PoE hub. • Your PoE hub must be connected to the router. Refer to the operating instructions included with the PoE hub for connection instructions. • The lens will pan and tilt when the camera is turned on. 2. Connect a LAN cable to a LAN port of the PoE hub and to a LAN port of the router. • Confirm that the indicator lights green after about 1 minute. If the indicator does not light green, see 1.2 Camera Indicator Issues in the Troubleshooting Guide on the CD-ROM. PoE indicator To the power supply PoE hub Green • When the lens pans or tilts, a sound can be heard from the camera. This is normal. • Use a 4-pair UTP/STP cable. • Do not use a relay connector or a hub between the camera and the PoE hub. These devices may disturb the data or electricity transmission. • If the PoE hub has indicators, the indicator lights as shown in the table below. Indicator Description LINK Turns on when the data is transmitted from the camera. PoE Turns on when the electricity is supplied to the camera. • If the PoE hub is turned off or power supply is temporarily cut off by the disconnection of the LAN cable, it may take time for the PoE hub's indicators to light. • The indicator display differs depending on manufacturers, refer to the manuals of the PoE hub. When connecting the camera using the AC Adaptor (Optional) Connect the camera to your router and to the power outlet as described below. LINK indicator LAN cable (Cat-5 straight cable) Router Modem Internet PC 1. Connect the LAN cable to the camera and the router. 2. Connect the AC adaptor cord to the DC IN jack. 3. Connect the AC cord to the AC adaptor, then plug the AC cord into the power outlet. • The lens will pan and tilt when the camera is turned on. • Confirm that the indicator lights green after about 1 minute. If the indicator does not light green, see 1.2 Camera Indicator Issues in the Troubleshooting Guide on the CD-ROM. Green To the power outlet LAN cable (Cat-5 straight cable) Router • When you operate the camera, the power outlet should be near the camera and easily accessible. • Use only specified Panasonic AC adaptor (Model No. BB-HCA7A, BB-HCA7CE, BB-HCA7E). • When the lens pans or tilts, a sound can be heard from the camera. This is normal. AC cord AC adaptor (BB-HCA7A, BB-HCA7CE, BB-HCA7E) Modem Internet PC After the camera's indicator turns green, you may set up the camera. Continue by following the procedure described in the included Setup Guide. • If the indicator does not turn green, see 1.2 Camera Indicator Issues in the Troubleshooting Guide on the included CD-ROM. After setting up the camera according to the procedure described in the Setup Guide, read the following information. Connecting External Audio Devices You can connect an external microphone and external speaker to the camera to use the Listen and Talk features, respectively. For information about these features, see 1.2.11 Audio Features in the Operating Instructions on the CD-ROM. Connect the devices as shown below. To microphone Microphone cable (φ 3.5 mm plug) To speaker For speaker (Output impedance For microphone (Plug-in power +3.3 V) 560 Ω line level) Note • If you use an external microphone, excessive cable length or a poor quality cable can cause degradation in audio quality. • The microphone cable should be no longer than 7 m (23 feet). • Use a speaker with a built-in amplifier. The speaker connects to the camera with a stereo audio cable similar to that used by your PC. The output signal is mono. • Make sure the camera and speaker are turned off when connecting or disconnecting the speaker cable, otherwise noise may be heard from the speaker. • The external microphone input does not correspond to a line level. Audio may be distorted when the line level is input. Audio distortion will be solved if you insert the following circuits. Under no circumstance should high-level audio, such as from a speaker, be connected to this input terminal. Doing so is likely to damage the camera. Speaker cable (φ 3.5 mm stereo plug) Camera Microphone Input Resistor 33 K Capacitor 1 F Audio Line Out 2