Panasonic BL-MS103A BL-MS103A Owner's Manual (English) - Page 155

CONNECTIVITY, INDICATORS ON THE BL-WV10A, Re-perform Quick Setup.

Get Panasonic BL-MS103A PDF manuals and user guides View all Panasonic BL-MS103A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

16 Troubleshooting the BL-WV10A 16.8 Connectivity Issue Causes and Solutions You cannot connect to a To register MAC address filtering for a wirelesscamera after registering it compatible camera, register both MAC addresses for the MAC address filter. assigned to the camera (the MAC addresses for the camera's wired interface and its wireless interface). Refer to the Operating Instructions included with your camera for information on confirming the camera's MAC addresses. 16.9 Indicators on the BL-WV10A Issue After turning the power on, the indicator is either solid amber or flashing amber. The indicator continues to flash green. The indicator continues to flash red. The indicator is red. The indicator does not turn green when using the wireless LAN. Causes and Solutions The Ethernet cable is not correctly connected. • Re-connect the Ethernet cable. The router is not working properly. • Check the router. You are attempting to connect a BL-C30A in wired mode but the wired/wireless switch is set to wireless, or you are attempting to work in a wireless mode and the wired/wireless switch is set to wired. • Set the switch to the appropriate setting. The wireless settings are different for the router and the BL-WV10A. (for wireless cameras) • Re-perform Quick Setup. The Quick Setup settings are incomplete. • Re-perform Quick Setup. There is something wrong with a camera. • Contact your dealer. Privacy Mode is turned on. • Either press the PRIVACY button on the front of the camera or turn off Privacy Mode (see page 111). The signal is bad. (for wireless cameras) • Change the camera location, remove any potential obstructions and try the connection again. [For assistance, please call: 1-800-272-7033] 155

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
16
Troubleshooting the BL-WV10A
[For assistance, please call: 1-800-272-7033]
155
16.8
Connectivity
16.9
Indicators on the BL-WV10A
Issue
Causes and Solutions
You cannot connect to a
camera after registering it
for the MAC address filter.
To register MAC address filtering for a wireless-
compatible camera, register both MAC addresses
assigned to the camera (the MAC addresses for the
camera’s wired interface and its wireless interface).
Refer to the Operating Instructions included with your
camera for information on confirming the camera’s
MAC addresses.
Issue
Causes and Solutions
After turning the power on,
the indicator is either solid
amber or flashing amber.
The Ethernet cable is not correctly connected.
•
Re-connect the Ethernet cable.
The router is not working properly.
•
Check the router.
You are attempting to connect a BL-C30A in wired
mode but the wired/wireless switch is set to
wireless, or you are attempting to work in a
wireless mode and the wired/wireless switch is
set to wired.
•
Set the switch to the appropriate setting.
The wireless settings are different for the router
and the BL-WV10A. (for wireless cameras)
•
Re-perform Quick Setup.
The indicator continues to
flash green.
The Quick Setup settings are incomplete.
•
Re-perform Quick Setup.
The indicator continues to
flash red.
There is something wrong with a camera.
•
Contact your dealer.
The indicator is red.
Privacy Mode is turned on.
•
Either press the PRIVACY button on the front
of the camera or turn off Privacy Mode (see
page 111).
The indicator does not
turn green when using the
wireless LAN.
The signal is bad. (for wireless cameras)
•
Change the camera location, remove any
potential obstructions and try the connection
again.