Panasonic CQC3305U CQC3305U User Guide - Page 6

Preparation Cancellation of Demonstration The demonstration message appears for initial use. 1 Set your car's ignition switch to the ACC or ON position. 5 Turn [VOL] counterclockwise. For using the remote control, press [0] (). 2 Press [PWR] (Power). 3 Hold down [VOL] (PUSH SEL: Select) for 2 sec. or more to open the menu. 4 Press [VOL] (PUSH SEL: Select) to select the Demonstration setting. ("DEMO" is displayed) Notes: • To return to the regular mode, press [DISP]. • Refer to the section on "Function Setting" ( page 23). • When "NO DISC" is displayed, the Demonstration cannot be cancelled. Preparation Before Initial Use Pull the insulation film out from the backside of remote control gently. Warning Keep batteries and insulation film out of reach of infants. If an infant ingests a battery, please seek immediate medical attention. Insulation film Battery Replacement Remove the battery holder with the remote control unit placed on a flat surface.  Stick your thumbnail into the groove, and push the holder in the direction of the arrow, and at the same time.  Pull it out in the direction of the arrow using a tough pointed object.  Put a battery in the case with () side facing up.  Put the case back. Tough pointed object   Back side   Cautions • Remove and dispose of an old battery immediately. • Do not disassemble, heat or short a battery. Do not throw a battery into a fire or water. • Follow local regulations when disposing of a battery. • Improper use of a battery may cause overheating, an explosion or ignition, resulting in injury or a fire. Notice This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Note: Battery Information: Battery Type: Panasonic lithium battery (CR2025) (Included in the remote control) Battery Life: Approximately 6 months under normal use (at room temperature) Remote Control Preparation Clock Adjustment The 12-hour system is used for the clock. 1 Press [PWR] (Power). 2 Press [DISP]. 3 Hold down [DISP] for 2 sec. or more. 4 Adjust the hour and press [DISP]. []: Forward []: Backward 5 Adjust the minute and press [DISP] to confirm the adjustment. []: Forward []: Backward Notes: • Adjust the clock when "ADJUST" appears on the display. • Hold down [] or [] to change numbers rapidly. • When "NO DISC" is displayed, the clock cannot be adjusted. 10 CQ-C3405U/C3305U General This chapter explains how to turn on or off the power, how to adjust the volume, etc. Power on Press [PWR] (Power). Power off Hold down [PWR] (Power) for 1 sec. or more. Power On/off (PWR: Power) Face Plate Removing/Mounting (Anti-Theft System) You can remove the face plate to prevent it from being stolen. Removing 1 Turn off the power. ( above) 2 Press [OPEN]. The face plate will be opened. 3 Push the face plate to the left. 4 Pull it out toward you. 5 Put the face plate in the case. Mounting 1 Fit the face plate with its left hole on the left pin provided on the main unit. 2 Fit the other hole on the other pin applying slight pressure. Cautions • This face plate is not waterproof. Do not expose it to water or excessive moisture. • Do not remove the face plate while driving your car. • Do not place the face plate on the dashboard or nearby areas where the temperature rises to high. • Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. • If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth. • To avoid damaging the face plate, do not push it down or place objects on it while it is open. The display changes as follows every time [DISP] is pressed. At power-off: Clock display (Default) At power-on: When the power is set to ON, refer to the description for each source mode. Display off CQ-C3405U/C3305U 11 Display Change (DISP: Display) Preparation, General English