Panasonic CQDP133U Auto Radio/cd Deck - Page 13
Continued, Final Checks, Preparation, Final Installation, Dashboard Installation - cq dp133u wiring diagram
UPC - 037988756056
View all Panasonic CQDP133U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
E N G Installation Guide (Continued) L I S H Speakers ❐ Final Checks Connect the speaker wires. See the wiring diagram 15 (➡ page 28) for the proper hookups. Follow the di- 1. Make sure that all wires are properly connected agram carefully to avoid damaging the speakers and insulated. and the stereo unit. The speakers used must be able to handle more 2. Make sure that the stereo unit is securely held in the mounting collar. than 45 W of audio power. If using an optional 3. Turn on the ignition to check the unit for proper audio amplifier, the speakers should be able to han- operation. dle the maximum amplifier output power. Speakers with low input ratings can be damaged. Speaker impedance should measure 4-8 Ω, which is typically marked on most speakers. Lower or higher If you have difficulties, consult your nearest authorized professional installer for assistance. ❐ Preparation impedance speakers will affect output and can cause both speaker and stereo unit damage. • We strongly recommend that you wear gloves Motor Antenna Connect the car motor antenna lead to the dark blue for installation work to protect yourself from injuries. motor antenna relay control lead. (Do not confuse the antenna lead with blue/white stripe lead for a power amplifier.) • When bending the mounting tabs of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. Battery Connect the yellow battery lead to the correct radio wire or to the battery fuse port on the fuse block. Antenna Connect the antenna by plugging the antenna lead into the antenna receptacle. • Disconnect the cable from the negative battery terminal (see cautions below). • Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. Equipment Connect any optional equipment such as an amplifier, according to the instructions furnished with the equipment. Leave about 12" (30 cm) of distance between the speaker leads/amplifier unit and the antenna/antenna extension cord. Read the operating and installation instructions of any equipment you will connect to this unit. Power Connect the red power lead to the correct car radio wire or to the appropriate fuse port on the fuse block. If the stereo unit functions properly with all these connections made, disconnect the wires and proceed to the final installation. ❐ Final Installation Lead Connections Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. Now insert the stereo unit into the mounting collar. Congratulations! After making a few final checks, you're ready to enjoy your new auto stereo system. Less than 30° Caution: Do not disconnect the battery terminals of a car with a trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. Dashboard Installation Installation Opening 23/32" (53 mm) 75/32" (182 mm) This unit can be installed in any dashboard having an opening as shown above. The dashboard should be 3⁄16" (4.75 mm)-7⁄32" (5.56 mm) thick in order to be able to support the unit. 24 CQ-DP133U/DP103U/DPX153U E N G L I Cautions: ¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries. S H ¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your 16 hands and fingers. First complete the electrical connections, and then check them for correctness.(a page 28) The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model. 1 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. The tabs to be bent vary depending on the car. To securely install the unit, fully bend a number of the tabs so that there is no rattling. Example: Tab y Power Connector q Mounting Collar Mounting Springs (C) Engage the Mounting Springs (C) in the mounting holes of the Mounting Collar q firmly. Mounting Spring Mounting Hole Mounting Holes t Mounting Bolt 2 Establish the rear connection of the unit. After fixing Mounting Bolt t and Power Connector y, fix the rear of the unit to the car body by either method (a) or (b) shown below. 3 Insert Trim Plate i. 4 After installation reconnect the negative (-) battery terminal. (a) Using the rear support strap e r Tapping screw (5 mmø×16 mm) Fire wall of car 3 mmø w Hex. nut (5 mmø) e Rear support strap t Mounting bolt (5 mmø) q Mounting collar (b) Using the rubber cushion (option) Rear support bracket Rubber cushion (option) (provided on the car) t Mounting bolt (5 mmø) q Mounting collar 25 CQ-DP133U/DP103U/DPX153U