Panasonic ES-LA93 Operating Instructions Multi-lingual - Page 9

Cleaning with the self-cleaning recharger continued, Cleaning the shaver without the self-cleaning, - replacement foil and blades

Get Panasonic ES-LA93 PDF manuals and user guides View all Panasonic ES-LA93 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Cleaning with the self-cleaning recharger (continued) Follow the steps outlined below if the status lamp blinks or glows during the "Clean/Dry/Charge" course. Blinks Glows Correctly set the detergent cartridge and then restart a course. If the status lamp goes out Continue a course. Remove the shaver from the selfcleaning recharger and then check that the [CLEAN] lamp has gone out. (Be careful as the blade may be hot or wet.) Check that the water tank is correctly attached, the water tank cap is securely closed and the selfcleaning recharger is placed horizontally. When an abnormality has been corrected Press and hold [SELECT] for approximately 2 seconds to turn off the status lamp and then restart a course. When no abnormality was found It is time to replace the detergent cartridge and cleaning liquid inside the water tank. Drain the old cleaning liquid inside the water tank and then refill it with water. Replace the old detergent cartridge and then restart the course. When the status lamp goes out Continue a course. When the status lamp glows again Contact an authorized service center. Cleaning the shaver without the self-cleaning recharger We recommend that you clean your shaver with the self-cleaning recharger or the "sonic" vibration turbo-cleaning mode when the faucet symbol appears on the LCD panel. 1. Disconnect the power cord from the shaver. 2. Apply some hand soap and some water to the outer foil. 3. Slide the switch lock button downwards to unlock the OFF/ ON switch. 4. Press the OFF/ON switch for more than 2 seconds to activate the turbo mode for 7 "sonic" vibration cleaning. • appears on the LCD panel. • After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the OFF/ON switch. 5. Remove the outer foil section and press the OFF/ON switch for more than 2 seconds to activate the turbo mode for "sonic" vibration cleaning and clean it with running water. 6. Wipe off any drops of water with a dry cloth.  English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
9
English
Cleaning with the self-cleaning recharger (continued)
Follow the steps outlined below if the status lamp blinks or glows
during the “Clean/Dry/Charge” course.
Blinks
Glows
Correctly set the
detergent cartridge and
then restart a course.
Remove the shaver from the self‑
cleaning recharger and then
check that the [CLEAN] lamp has
gone out. (Be careful as the blade
may be hot or wet.) Check that
the water tank is correctly
attached, the water tank cap is
securely closed and the self‑
cleaning recharger is placed
horizontally.
If the status lamp goes
out
Continue a course.
When an abnormality has
been corrected
When no abnormality was
found
Press and hold [SELECT] for
approximately ± seconds to
turn off the status lamp and
then restart a course.
It is time to replace the
detergent cartridge and
cleaning liquid inside the water
tank.
Drain the old cleaning liquid
inside the water tank and then
refill it with water. Replace the
old detergent cartridge and
then restart the course.
When the status lamp
goes out
When the status lamp glows
again
Continue a course.
Contact an authorized service
center.
Cleaning the shaver without the self-cleaning
recharger
We recommend that you clean
your shaver with the self‑cleaning
recharger or the “sonic” vibration
turbo‑cleaning mode when the
faucet symbol
appears on the
LCD panel.
1. Disconnect the power cord
from the shaver.
±. Apply some hand soap and
some water to the outer foil.
3. Slide the switch lock button
downwards to unlock the OFF/
ON switch.
4. Press the OFF/ON switch for
more than ± seconds to
activate the turbo mode for
“sonic” vibration cleaning.
appears on the LCD
panel.
After about ±0 seconds, it
will be automatically turned
off, or you can turn it off by
pressing the OFF/ON switch.
5. Remove the outer foil section
and press the OFF/ON switch
for more than ± seconds to
activate the turbo mode for
“sonic” vibration cleaning and
clean it with running water.
6. Wipe off any drops of water
with a dry cloth.
•
•
7