Panasonic EY4541 EY4541 User Guide - Page 11

Adjusting the orbital stroke mode, Anti-splintering plate, Dust adapter for vacuum cleaner, EY9H009E

Get Panasonic EY4541 - JIGSAW 14.4V - MULTI LANGUAGE PDF manuals and user guides View all Panasonic EY4541 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Adjusting the orbital stroke mode • Adjust the orbital stroke mode to the object to be cut. 32 1 0 Lever position 0 1 Blade movement Vertical only Main applications • Cutting hard metals such as steel • Smooth cutting of building materials and plywood boards • Cutting around small curves • Cutting softer metals such as aluminum and other non-ferrous metals • Cutting hardwood, plywood boards and plastics Low orbital stroke mode • Cutting fairly soft materials • Cutting wood and composite boards 2 • High-speed cutting of aluminum and soft steel Medium orbital stroke mode •Cutting soft mate- rials • High-speed cutting of materials such 3 as wood, composite boards and plastics High orbital stroke mode • If you would like to produce a cleaner finish, set the orbital stroke mode to a lower level. Anti-splintering plate Use the anti-splintering plate to reducing splinter while cutting wood. Installation 1. Set the base at 90 degree position. 2. Place the anti-splintering plate on the underside of the base, and gently push it to be installed. • Install so that the beveled edge of the slot in the middle of the anti-splintering plate is facing toward the jigsaw. Dust adapter for vacuum cleaner (EY9H009E) (Available as an accessory, not included) You can use a vacuum cleaner to collect cutting dust while cutting. Installation 1. Attach the hook of the dust collec-tion adapter to the front of the base. 2. Snap the rear to install it. 3. Attach the hose of the vacuum cleaner. • It is recommended to use a dust adapter for reducing the risk of damaging the surface of the object being cut. - 11 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Adjusting the orbital stroke mode
• Adjust the orbital stroke mode to the
object to be cut.
3
2
1
0
Lever
position
Blade
movement
Main
applications
0
Vertical only
• Cutting hard met-
als such as steel
• Smooth cutting of
building materi-
als and plywood
boards
• Cutting around
small curves
1
Low orbital stroke
mode
• Cutting softer met-
als such as alu-
minum and other
non-ferrous metals
•
Cutting hardwood,
plywood boards
and plastics
2
Medium orbital
stroke mode
• Cutting fairly soft
materials
• Cutting wood and
composite boards
• High-speed cut-
ting of aluminum
and soft steel
3
High orbital
stroke mode
• Cutting soft mate-
rials
• High-speed cutting
of materials such
as wood, com-
posite boards and
plastics
• If you would like to produce a cleaner
finish, set the orbital stroke mode to a
lower level.
Anti-splintering plate
Use the anti-splintering plate to re-
ducing splinter while cutting wood.
Installation
1. Set the base at 90 degree position.
2. Place the anti-splintering plate on the
underside of the base, and gently
push it to be installed.
• Install so that the beveled edge of the
slot in the middle of the anti-splinter-
ing plate is facing toward the jigsaw.
Dust adapter for vacuum cleaner
(EY9H009E) (Available as an
accessory, not included)
You can use a vacuum cleaner to col-
lect cutting dust while cutting.
Installation
1. Attach the hook of the dust collec-tion
adapter to the front of the base.
2. Snap the rear to install it.
3. Attach the hose of the vacuum
cleaner.
• It is recommended to use a dust adapt-
er for reducing the risk of damaging the
surface of the object being cut.
-
11
-