Panasonic EY4541 EY4541 User Guide - Page 14

Control Panel

Get Panasonic EY4541 - JIGSAW 14.4V - MULTI LANGUAGE PDF manuals and user guides View all Panasonic EY4541 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Cutting at the same width Control Panel 1. Place the base onto the workpiece so that the edge of the rip fence and workpiece are put together. (1) (3) 2. Without letting the blade touch the workpiece, turn on the power switch. 3. Face the rip fence firmly to the workpiece to cut parallel line. Cutting circles 1. If cutting away a section, make a drill hole on workpiece to let the jigsaw blade pass through. 2. Align the pin hole of the rip fence with the center of the circle, and then use a nail or screw to hold the object in place. (1) LED light (2) Before the use of LED light, always pull the power switch once. Press the LED light button. The light illuminates with very low current, and it does not adversely affect the performance of the driver during use or its battery capacity. CAUTION: • The built-in LED light is designed to il- luminate the small work area temporarily. • Do not use it as a substitute for a regular flashlight, since it does not have enough brightness. • LED light turns off when the tool has not been used for 5 minutes. Caution : DO NOT STARE INTO BEAM. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. 3. Without touching the workpiece, turn on the power switch. 4. Cut along the marked line. - 14 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Cutting at the same width
1. Place the base onto the workpiece
so that the edge of the rip fence and
workpiece are put together.
2. Without letting the blade touch the
workpiece, turn on the power switch.
3. Face the rip fence firmly to the work-
piece to cut parallel line.
Cutting circles
1. If cutting away a section, make a drill
hole on workpiece to let the jigsaw
blade pass through.
2. Align the pin hole of the rip fence with
the center of the circle, and then use
a nail or screw to hold the object in
place.
3. Without touching the workpiece, turn
on the power switch.
4. Cut along the marked line.
Control Panel
Control Panel
(1)
(3)
(2)
(1) LED light
Before the use of LED
light, always pull the
power switch once.
Press
the LED
light button.
The light illuminates
with very low cur-
rent, and it does not
adversely affect the
performance of the
driver during use or
its battery capacity.
CAUTION:
• The built-in LED light is designed to il-
luminate the small work area tempo-
rarily.
• Do not use it as a substitute for a reg-
ular flashlight, since it does not have
enough brightness.
• LED light turns off when the tool has
not been used for 5 minutes.
Caution
: DO NOT STARE INTO BEAM.
Use of controls or adjustments or perform-
ance of procedures other than those spec-
i
fi
ed herein may result in hazardous radia-
tion exposure.
-
14
-