Panasonic EY4542 EY4542 User Guide - Page 14

Control Panel

Get Panasonic EY4542 - CIRCULAR SAW 14.4V PDF manuals and user guides View all Panasonic EY4542 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Caution : DO NOT STARE INTO BEAM. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. (2) Overheat warning lamp Fig. 12 NOTE: When the tool has difficulty in ejecting or collecting dust, the dust outlet may be clogged with dust. Open the front cover and remove any dust. Control Panel (1) (2) (3) (1) LED light LED light Off (normal operation) Flashing: Overheat Indicates operation has been halted due to battery overheating. The overheating protection feature halts tool operation to protect the battery pack in the event of overheating. The overheat warning lamp on the control panel flashes when this feature is active. • If the overheating protection feature activates, allow the tool to cool thoroughly (at least 30 minutes). The tool is ready for use when the overheat warning lamp goes out. • Avoid using the tool in a way that causes the overheating protection feature to activate repeatedly. (3) Battery low warning lamp Off (normal operation) Flashing (No charge) Battery protection feature active Fig. 13 Before the use of LED light, always pull the power switch once. Press the LED light on button. The light illuminates with very low current, and it does not adversely affect the performance of the tool during use or its battery capacity. CAUTION: • The built-in LED light is designed to illuminate the small work area temporarily. • Do not use it as a substitute for a regular flashlight, since it does not have enough brightness. • LED light turns off when the tool has not been used for 5 minutes. Excessive (complete) discharging of lithium ion batteries shortens their service life dra-matically. The tool includes a battery protec-tion feature designed to prevent excessive discharging of the battery pack. • The battery protection feature activates imme- diately before the battery loses its charge, causing the battery low warning lamp to flash. • If you notice the battery low warning lamp flashing, charge the battery pack immediately. - 14 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
-
14
-
Fig. 1±
NOTE:
When the tool has difficulty in ejecting or col-
lecting dust, the dust outlet may be clogged
with dust. Open the front cover and remove
any dust.
Control Panel
(1)
(±)
(3)
(1) LED light
LED light
Fig. 13
Before the use of LED light, always pull the
power switch once.
Press
the LED light on button.
The light illuminates with very low current, and it
does not adversely affect the performance of the
tool during use or its battery capacity.
CAUTION:
• The built-in LED light is designed to illuminate the
small work area temporarily.
• Do not use it as a substitute for a regular flashlight,
since it does not have enough brightness.
• LED light turns off when the tool has not been
used for ² minutes.
Caution
: DO NOT STARE INTO BEAM.
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
(2) Overheat warning lamp
The overheating protection feature halts tool
operation to protect the battery pack in the event
of overheating. The overheat warning lamp on
the control panel flashes when this feature is
active.
• If the overheating protection feature activates,
allow the tool to cool thoroughly (at least 30
minutes). The tool is ready for use when the
overheat warning lamp goes out.
• Avoid using the tool in a way that causes the
overheating protection feature to activate
repeatedly.
(3) Battery low warning lamp
Excessive (complete) discharging of lithium ion
batteries shortens their service life dra-matically.
The tool includes a battery protec-tion feature
designed to prevent excessive discharging of
the battery pack.
• The battery protection feature activates imme-
diately before the battery loses its charge,
causing the battery low warning lamp to flash.
• If you notice the battery low warning lamp
flashing, charge the battery pack immediately.
Off
(normal
operation)
Flashing: Overheat
Indicates operation has
been halted due to battery
overheating.
Off
(normal
operation)
Flashing
(No charge)
Battery protection
feature active