Panasonic EY7440 EY7440 User Guide - Page 7

Operation - drill

Get Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG PDF manuals and user guides View all Panasonic EY7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Attaching or Removing Bat­ tery Pack 1. To connect the battery pack: Line up the alignment marks and at­ tach the battery pack. • Slide the battery pack until it locks into position. Switch and Forward/Reverse Lever Operation Forward Reverse Alignment marks 2. To remove the battery pack: Push on the button from the front to re­lease the battery pack. Button V. OPERATION [Main Body] Switch Operation 1. The speed increases with the amount of depression of the trigger. When begin­ning work, depress the trigger slightly to start the rotation slowly. 2. A feedback electronic controller is used to give a strong torque even in low speed. 3. The brake operates when the trigger is released and the motor stops immediately. NOTE: When the brake operates, a braking sound may be heard. This is normal. Switch lock CAUTION: To prevent damage, do not operate Forward/Reverse lever until the bit comes to a complete stop. Forward Rotation Switch Operation 1. Push the lever for forward rotation. 2. Depress the trigger switch slightly to start the tool slowly. 3. The speed increases with the amount of depression of the trigger for efficient tightening of screws and drilling. The brake operates and the chuck stops immediately when the trigger is released. 4. After use, set the lever to its center position (switch lock). Reverse Rotation Switch Operation 1. Push the lever for reverse rotation. Check the direction of rotation before use. 2. Depress the trigger switch slightly to start the tool slowly. 3. After use, set the lever to its center position (switch lock). Clutch Torque Setting Adjust the torque to one of the 18 clutch set­tings or " " position. CAUTION: Test the setting before actual opera­ tion. -  -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
-
7
-
Attaching or Removing Bat-
tery Pack
1. To connect the battery pack:
Line up the alignment marks and at-
tach the battery pack.
• Slide the battery pack until it locks
into position.
Alignment marks
±. To remove the battery pack:
Push on the button from the front to
release the battery pack.
Button
V
.
OPERATION
[Main Body]
Switch Operation
1. The speed increases with the
amount of depression of the trigger.
When beginning work, depress the
trigger slightly to start the rotation
slowly.
±. A feedback electronic controller is
used to give a strong torque even in
low speed.
3. The brake operates when the trig-
ger is released and the motor stops
immediately.
NOTE:
When the brake operates, a braking
sound may be heard. This is normal.
Switch and Forward/Reverse
Lever Operation
Forward
Reverse
Switch lock
CAUTION:
To prevent damage, do not operate
Forward/Reverse lever until the bit
comes to a complete stop.
Forward Rotation Switch
Operation
1. Push the lever for forward rotation.
±. Depress the trigger switch slightly to
start the tool slowly.
3. The speed increases with the
amount of depression of the trigger
for efficient tightening of screws and
drilling. The brake operates and the
chuck stops immediately when the
trigger is released.
4. After use, set the lever to its center
position (switch lock).
Reverse Rotation Switch
Operation
1. Push the lever for reverse rotation.
Check the direction of rotation be-
fore use.
±. Depress the trigger switch slightly to
start the tool slowly.
3. After use, set the lever to its center
position (switch lock).
Clutch Torque Setting
Adjust the torque to one of the 18
clutch settings or “
” position.
CAUTION
:
Test the setting before actual opera-
tion.