Panasonic EY7440 EY7440 User Guide - Page 9

To Set the Belt Hook Angle, Position, To Change the Belt Hook, Location Side, Control Panel - drill driver

Get Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG PDF manuals and user guides View all Panasonic EY7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

• When the belt hook is not used, be sure to return it to the storing position. The belt hook may catch on something. This may result in an accident or injury. • When the unit is hooked onto the waist belt by the belt hook, do not attach driver bits to the unit. A sharp edge object, such as a drill bit, may cause injury or an accident. To Set the Belt Hook Angle Position 1.Slide the belt hook lock lever 1 and hold it to unlock the belt hook. 2.P u l l t h e b e l t h o o k from storing position 2 2 and set it. 1 3.Release the belt hook lock lever to lock the 3 angle of belt hook. 4.Make sure the belt hook is firmly locked. Also make sure the belt hook is firmly locked into position 3. • The belt hook cannot be locked in this position. Firmly lock it into position before use. To return the belt hook to the storing position, follow step 1. and 2. above, then lower the belt hook. To secure the lock, follow 3 and 4 above. To Change the Belt Hook Location Side The belt hook can be attached to either side of the unit. 4.Fasten the screw firmly, turning it clockwise. The belt hook can be taken out from the main unit only when it is at storing position. Control Panel (3) (1) (2) (1) LED light Pressing toggles the LED light on and off. The light illuminates with very low current, and it does not adversely affect the performance of the driver during use or its battery capacity. CAUTION: • The built-in LED light is designed to illuminate the small work area temporarily. • Do not use it as a substitute for a regular flashlight, since it does not have enough brightness. This product has the built-in LED light. This product is classified into "Class 1 LED Product" to EN 60825-1 Class 1 LED Product Caution : DO NOT STARE INTO BEAM. (2) Overheat warning lamp 1.Set the belt hook at storing position. 2.Loosen the screw turning it counter-clockwise, using a flat metal or a flat blade screw driver. 3.Take out the belt hook and insert into the other side of the slot on the main unit. Off (normal operation) Flashing: Overheat Indicates operation has been halted due to battery overheating. The overheating protection feature halts driver operation to protect the battery pack in the event of over­ heating. The overheat warning lamp -  -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
-
9
-
• When the belt hook is not used, be
sure to return it to the storing posi-
tion. The belt hook may catch on
something.
This may result in an accident or
injury.
•
When the unit is hooked onto the
waist belt by the belt hook, do not
attach driver bits to the unit. A sharp
edge object, such as a drill bit, may
cause injury or an accident.
To Set the Belt Hook Angle
Position
1. Slide the belt hook lock lever
1
and
hold it to unlock the belt hook.
2
1
3
±. Pull the belt hook
from storing position
2
and set it.
3.
Release the belt hook
lock lever to
lock the
angle of belt hook.
4.
Make sure the belt hook is firmly
locked. Also make sure the belt hook
is firmly locked into position
3
.
• The belt hook can-
not be locked in this
position. Firmly lock
it into position before
use.
To return the belt hook to the storing
position, follow step 1. and ±. above,
then lower the belt hook.
To secure the lock, follow 3 and 4
above.
To Change the Belt Hook
Location Side
The belt hook can be attached to
either side of the unit.
1. Set the belt hook at storing posi-
tion.
±. Loosen the screw turning it coun-
ter-clockwise, using a flat metal or
a flat blade screw driver.
3. Take out the belt hook and insert
into the other side of the slot on the
main unit.
4. Fasten the screw firmly, turning it
clockwise.
The belt hook can be taken out from
the main unit only when it is at storing
position.
Control Panel
(1)
(±)
(3)
(1) LED light
Pressing
toggles the
LED light on and off.
The light illuminates with
very low current, and it
does not adversely affect
the performance of the
driver during use or its bat-
tery capacity.
CAUTION:
• The built-in LED light is designed to
illuminate the small work area tem-
porarily.
•
Do not use it as a substitute for a
regular
flashlight, since it does not
have enough brightness
.
This product has the built-in LED light.
This product is classified into
“
Class 1
LED Product
”
to EN 608±5-1
Class 1 LED Product
Caution
: DO NOT STARE INTO BEAM.
(2) Overheat warning lamp
Off
(normal
operation)
Flashing: Overheat
Indicates operation has
been halted due to battery
overheating.
The overheating protection feature
halts driver operation to protect the
battery pack in the event of over-
heating. The overheat warning lamp