Panasonic KX-TAW84868 Installation Manual - Page 115

Operation

Get Panasonic KX-TAW84868 - Extension Caller Id Card PDF manuals and user guides
UPC - 037988850976
View all Panasonic KX-TAW84868 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

4.1.3 Operation 4.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION • The APT does not ring. • The ringer volume is off. • Turn on the ringer volume. • During a power failure, • An APT is connected to the • Disconnect the APT and connect an extensions connected to extension port. SLT. ports 1 and 2 of Hybrid Ports • The dialing mode (tone or • Set the Tone/Pulse switch to the other do not operate. pulse) is incorrect. position. • Originating an outside call, • The corresponding CO • Program the CO button. Refer to call transfer, or conference button does not exist on the "1.18.2 Flexible Buttons" in the Feature cannot be performed. APT. Guide. • Cannot register the PS. • Wrong Personal • Register the PIN set to the PBX into the Identification Number (PIN) PS. is registered to the PS. • CS is not connected properly. • Make sure that the cable is connected properly with correct pin assignments. Also, make sure that the cable does not make short circuits. • Switch all DIP switches off. • PS becomes out of range. • CS is not working. • Cannot make calls using the PS. • Make sure that the cable is connected properly with correct pin assignments. Also, make sure that the cable does not make short circuits. • Switch all DIP switches off. • Location of CS is not good. • Locate the CS properly (refer to "2.7.5 Site Survey" ). • Access system of the PS is • Change the access system setting of not properly set. the PS to the appropriate system or automatic. • Noise is frequent while using • Call handover is not • Locate the CS properly (refer to "2.7.5 the PS. working while using the PS. Site Survey" ). • Conversations disconnect • PS is out of CS coverage while using the PS. area. • PS stays out of service when the CS status is changed from Out of Service to In Service. • It may take about 10 s for • Wait until the CS starts up. CS to start up after the status has been changed to In Service. Installation Manual 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
4.1 Troubleshooting
Installation Manual
115
4.1.3
Operation
PROBLEM
PROBABLE CAUSE
SOLUTION
•
The APT does not ring.
•
The ringer volume is off.
•
Turn on the ringer volume.
•
During a power failure,
extensions connected to
ports 1 and 2 of Hybrid Ports
do not operate.
•
An APT is connected to the
extension port.
•
The dialing mode (tone or
pulse) is incorrect.
•
Disconnect the APT and connect an
SLT.
•
Set the Tone/Pulse switch to the other
position.
•
Originating an outside call,
call transfer, or conference
cannot be performed.
•
The corresponding CO
button does not exist on the
APT.
•
Program the CO button. Refer to
"1.18.2 Flexible Buttons" in the Feature
Guide.
•
Cannot register the PS.
•
Wrong Personal
Identification Number (PIN)
is registered to the PS.
•
Register the PIN set to the PBX into the
PS.
•
CS is not connected
properly.
•
Make sure that the cable is connected
properly with correct pin assignments.
Also, make sure that the cable does not
make short circuits.
•
Switch all DIP switches off.
•
PS becomes out of range.
•
Cannot make calls using the
PS.
•
CS is not working.
•
Make sure that the cable is connected
properly with correct pin assignments.
Also, make sure that the cable does not
make short circuits.
•
Switch all DIP switches off.
•
Location of CS is not good.
•
Locate the CS properly (refer to "2.7.5
Site Survey" ).
•
Access system of the PS is
not properly set.
•
Change the access system setting of
the PS to the appropriate system or
automatic.
•
Noise is frequent while using
the PS.
•
Conversations disconnect
while using the PS.
•
Call handover is not
working while using the PS.
•
PS is out of CS coverage
area.
•
Locate the CS properly (refer to "2.7.5
Site Survey" ).
•
PS stays out of service
when the CS status is
changed from Out of
Service to In Service.
•
It may take about 10 s for
CS to start up after the
status has been changed to
In Service.
•
Wait until the CS starts up.