Panasonic PT-LB10U Portable Projector - Page 6

Accessories, Before use, Caution when moving the projector, Cautions regarding setting-up - model is

Page 6 highlights

NOTICE: B This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: Accessories Check that all of the accessories shown below have been included with your projector. Card remote control unit Lithium battery for (TNQE239 x1) remote control unit (CR2025 x1) RGB signal cable [1.8 m (5´10˝), K1HA15DA0002 x1] POWER INPUT VIDEO RGB AUTO SETUP MENU ENTER FREEZE SHUTTER STD VOLUME INDEX WINDOW D.ZOOM Power cord Carrying bag (K2CG3DR00005 x 1) (TPEP009 x 1) PROJECTOR PT-LB10NTU only CD-ROM Wireless Card (TQBH9005 x1) (N5HBD0000028 x1) Hexagon wrench (TKLA0701 x1) 10-ENGLISH Before use Caution when moving the projector Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory carrying bag. When placing the projector inside the carrying bag, position it so that the lens is facing upward. Do not put anything else in the bag other than the projector and the cables. Cautions regarding setting-up Avoid setting up in places which are subject to vibration or shocks. The internal parts can be damaged, which may cause malfunctions or accidents. Do not set up the projector near high-voltage power lines or near motors. The projector may be subject to electromagnetic interference. If installing the projector to the ceiling, ask a qualified technician to carry out all installation work. You will need to purchase the separate installation kit (Model No.ET-PKC80). Furthermore, all installation work should only be carried out by a qualified technician. If using this projector at high elevations (above 1 400 m), set the "FAN CONTROL" to "HIGH". (Refer to page 45.) Failure to observe this may result in malfunctions. ENGLISH-11 Preparation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33

E
NGLISH
-11
Preparation
10-E
NGLISH
Before use
Caution when moving the projector
Be sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. When
moving the projector, use the accessory carrying bag. When placing the
projector inside the carrying bag, position it so that the lens is facing upward.
Do not put anything else in the bag other than the projector and the cables.
Cautions regarding setting-up
Avoid setting up in places which are subject to vibration or shocks.
The internal parts can be damaged, which may cause malfunctions or
accidents.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
You will need to purchase the separate installation kit (Model No.ET-PKC80).
Furthermore, all installation work should only be carried out by a qualified
technician.
If using this projector at high elevations (above 1 400 m), set the “FAN
CONTROL” to “HIGH”. (Refer to page 45.)
Failure to observe this may result in malfunctions.
Card remote control unit
(TNQE239 x1)
Power cord
(K2CG3DR00005 x 1)
Carrying bag
(TPEP009 x 1)
Lithium battery for
remote control unit
(CR2025 x1)
RGB signal cable
[1.8 m (5´10˝),
K1HA15DA0002 x1]
Accessories
Check that all of the accessories shown below have been included with your
projector.
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME
D.ZOOM
STD
AUTO
SETUP
VIDEO
INPUT
POWER
RGB
MENU
CD-ROM
(TQBH9005 x1)
Wireless Card
(N5HBD0000028 x1)
Hexagon wrench
(TKLA0701
x1
)
PT-LB10NTU only
NOTICE:
B
This product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries