Panasonic PTAE3000U PTAE3000U User Guide - Page 45

TEMP and LAMP Indicators, Managing the indicated problems

Get Panasonic PTAE3000U - HOME THEATER LCD PROJECTOR PDF manuals and user guides View all Panasonic PTAE3000U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

TEMP and LAMP Indicators Managing the indicated problems If a problem should occur with the projector, the LAMP and/or TEMP indicators will inform you. Manage the indicated problems as follows. 1. Confirm the status of all indicators and projector, and switch off the projector in proper way. 2. Find out the cause of the problem by status of the LAMP and/or TEMP indicators. 3. Follow the following instruction for each indication and solve the problem. 4. Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer. Power LAMP TEMP J LAMP indicator Indicator Illuminating red Flashing red Problem Cause Remedy LAMP RUNTIME has reached 1 800 hours. The lamp unit will run out soon and needs to be replaced. See "Replacing the lamp unit" on page 47. Lamp circuit failure, abnormal function or lamp unit is damaged. The MAIN POWER is switched on again before the lamp unit is cooled enough. Let the lamp unit cool down and turn on the MAIN POWER after 90 seconds. Lamp circuit failure, abnormal function. Contact an Authorized Service Center. The lamp unit is damaged. See "Replacing the lamp unit" on page 47. J TEMP indicator Indicator Illuminating red while projecting and the alert will be displayed. Flashing red and the power button is turned off. Problem The temperature inside and/or outside the projector is abnormally high. Cause Remedy The ventilation openings are covered. Remove the object(s) from the ventilation openings or clear around the projector. The room temperature is too high. The air filter is excessively The projector is located at dirty and the ventilation is high elevations (above poor. 1 400 - 2 700 m). Reinstall the projector in a temperature controlled place. See page 54. Replace the air filter in the proper method. See page 46. Turn on the projector and set the HIGH ALTITUDE MODE to ON. See page 44. NOTE: • If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorized Service Center. Maintenance ENGLISH - 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
E
NGLISH - 45
Maintenance
TEMP and LAMP Indicators
If a problem should occur with the projector, the
LAMP
and/or
TEMP
indicators will inform you. Manage the indicated problems as follows.
1.
Confirm the status of all indicators and projector, and switch off
the projector in proper way.
2.
Find out the cause of the problem by status of the
LAMP
and/or
TEMP
indicators.
3.
Follow the following instruction for each indication and solve the
problem.
4.
Turn on the projector in the correct way and confirm the
indicator is not indicating a problem any longer.
LAMP indicator
TEMP indicator
Managing the indicated problems
Indicator
Illuminating red
Flashing red
Problem
LAMP RUNTIME
has
reached 1 800 hours.
Lamp circuit failure, abnormal function or lamp unit is damaged.
Cause
The lamp unit will run out
soon and needs to be
replaced.
The
MAIN POWER
is
switched on again before
the lamp unit is cooled
enough.
Lamp circuit failure,
abnormal function.
The lamp unit is
damaged.
Remedy
See “Replacing the lamp
unit” on page 47.
Let the lamp unit cool
down and turn on the
MAIN POWER
after
90 seconds.
Contact an Authorized
Service Center.
See “Replacing the lamp
unit” on page 47.
Indicator
Illuminating red while projecting and the alert will be displayed.
Flashing red and the power button is turned off.
Problem
The temperature inside and/or outside the projector is abnormally high.
Cause
The ventilation openings
are covered.
The room temperature is
too high.
The air filter is excessively
dirty and the ventilation is
poor.
The projector is located at
high elevations (above
1 400 - 2 700 m).
Remedy
Remove the object(s)
from the ventilation
openings or clear around
the projector.
Reinstall the projector in a
temperature controlled
place. See page 54.
Replace the air filter in the
proper method. See
page 46.
Turn on the projector and
set the
HIGH ALTITUDE
MODE
to
ON
.
See page 44.
NOTE:
•
If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorized Service Center.
Power
LAMP TEMP