Panasonic PTL200U PTL200U User Guide - Page 52

Remedy, Problem, Indicator, display, Possible, cause, LAMP indicator, HIGH Ask your

Get Panasonic PTL200U - LCD PROJECTOR PDF manuals and user guides View all Panasonic PTL200U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

LAMP indicator Indicator display Illuminated (red) It is nearly time to Problem replace the lamp unit. Flashing (red) An abnormality has been detected in the lamp circuit. B Does "REPLACE Possible cause LAMP" appear on the screen after the projector is turned on? B The power may have been turned on straight away after it was turned off. B There may be an abnormality in the lamp circuit. B This occurs when B Wait for a while B Turn off the MAIN the operation time until the lamp unit POWER switch by for the lamp unit is cools down before following the nearing 1800 turning the power procedure given hours. (when back on again. on page 23, and LAMP POWER then contact an Remedy has been set to "HIGH") Ask your Authorised Service Center. dealer or an Authorised Service Center to replace the lamp unit. NOTE: B Be sure to turn off the MAIN POWER switch by following the procedure given in "Turning off the power" on page 23 before carrying out any of the procedures in the "Remedy" column. B If the main power turns off after the TEMP indicator starts flashing, it means that an abnormality has occurred. Please contact an Authorised Service Center so that the necessary repairs can be made. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
52
Remedy
Problem
Indicator
display
Flashing (red)
It is nearly time to
replace the lamp
unit.
Illuminated (red)
An abnormality has been detected in the lamp
circuit.
B
Does “REPLACE
LAMP” appear on
the screen after
the projector is
turned on?
B
This occurs when
the operation time
for the lamp unit is
nearing 1800
hours. (when
LAMP POWER
has been set to
“HIGH”) Ask your
dealer or an
Authorised
Service Center to
replace the lamp
unit.
Possible
cause
B
The power may
have been turned
on straight away
after it was turned
off.
B
Wait for a while
until the lamp unit
cools down before
turning the power
back on again.
B
There may be an
abnormality in the
lamp circuit.
B
Turn off the MAIN
POWER switch by
following the
procedure given
on page 23, and
then contact an
Authorised
Service Center.
LAMP indicator
NOTE:
B
Be sure to turn off the MAIN POWER switch by following the procedure
given in “Turning off the power” on page 23 before carrying out any of the
procedures in the “Remedy” column.
B
If the main power turns off after the TEMP indicator starts flashing, it
means that an abnormality has occurred. Please contact an Authorised
Service Center so that the necessary repairs can be made.