Panasonic PVC923 PVC923 User Guide - Page 18

SETTING THE V-CHIP TO SET THE ON TIMER 5 Press the SET/TRACKING + or - button to select V-CHIP. 6 Press the ENTER button to display ON. 7 Press the MENU button until the MENU screen is cleared. V-CHIP SET V-CHIP : OFF TV RATING : TV-PG MOVIE RATING : PG-13 CHANGE PASSWORD 〈+/-/ENTER/MENU〉 V-CHIP SET V-CHIP : ON TV RATING : TV-PG MOVIE RATING : PG-13 CHANGE PASSWORD 〈+/-/ENTER/MENU〉 NOTE : The V-Chip function is activated only on programs and tapes that have the rating signal. To use the TV after the TV is protected. When the program applied to the V-Chip setting is received, enter the password, then press the ENTER button. When the password is entered correctly the protection will be temporarily overridden. If you forget the password... Disconnect the AC cord plug from AC outlet and leave the unit for more than two minutes. Insert the AC cord plug again, then turn the volume level into a minimum. Press the VOL - button on the unit and the 0 button on the remote control for more than 1 second simultaneously. TO CHANGE PASSWORD 1 Repeat the steps 1-3 on "TO REGISTER THE PASSWORD", then enter the Password using the Direct Channel Selection button (09), then press the ENTER button. V-CHIP SET PASSWORD: - - - - 〈0-9/ENTER/CANCEL/MENU〉 2 Press the SET/TRACKING + or - button to select CHANGE PASSWORD, then press the ENTER button. 3 Enter the new password using the Direct Channel Selection button (0-9), then press the ENTER button. 4 Enter the same password again to confirm, then press the ENTER button. 5 Press the MENU button repeatedly to return to normal screen. V-CHIP SET V-CHIP : ON TV RATING : TV-PG MOVIE RATING : PG-13 CHANGE PASSWORD á+/-/ENTER/MENUñ V-CHIP SET V-CHIP : ON TV RATING : TV-PG MOVIE RATING : PG-13 CHANGE PASSWORD NEW PASSWORD: - - - - 〈0-9/ENTER/CANCEL/MENU〉 V-CHIP SET V-CHIP : ON TV RATING : TV-PG MOVIE RATING : PG-13 CHANGE PASSWORD CONFIRM PASSWORD: - - - - 〈0-9/ENTER/CANCEL/MENU〉 18 This feature allows you to have the TV/VCR automatically turn on at a predetermined time. If you program the ON TIMER once, the TV/VCR will turn on on the programmed day (daily/weekly) at the same time to the same channel. EXAMPLE: Turning on the TV to channel 12 at 7:00 AM, MONDAY-FRIDAY. 1 Press the MENU button. Press the SET/TRACKING + or - button to select the TV SETUP option, then press the ENTER button. M E N U TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP á+/-/ENTER/MENUñ 2 Press the SET/TRACKING + or - button to select the ON/OFF TIMER option, then press the ENTER button. TV SETUP V-CHIP SET ON/OFF TIMER PICTURE á+/-/ENTER/MENUñ 3 Press the SET/TRACKING + or - button to select the ON TIMER option, then press the ENTER button. 4 Press the SET/TRACKING + or - button to set the desired hour, then press the ENTER button. ON/OFF TIMER ON TIMER 12:00AM CH001 SUN-SAT CANCEL OFF TIMER 12:00AM CANCEL á+/-/ENTER/CANCEL/MENUñ ON/OFF TIMER ON TIMER 7:00AM CH001 SUN-SAT CANCEL OFF TIMER 12:00AM CANCEL á+/-/ENTER/CANCEL/MENUñ 5 Set the desired minute, channel and daily or weekly timer date as in step 4. ON/OFF TIMER ON TIMER 7:00AM CH012 MON-FRI CANCEL OFF TIMER 12:00AM CANCEL 〈+/-/ENTER/CANCEL/MENU〉 6 Press the SET/TRACKING + or - button to select the SET mode, then press the ENTER button. Press the MENU button repeatedly to return to normal screen. ON/OFF TIMER ON TIMER 7:00AM CH012 MON-FRI SET OFF TIMER 12:00AM CANCEL 〈+/-/ENTER/CANCEL/MENU〉 NOTES: • The TV/VCR will automatically turn off approximately 1 hour later after the ON TIMER turns on if no OFF TIMER has been set. To continue watching the TV, press any button to cancel the one hour automatic shut off. • To cancel ON TIMER, follow above steps 1-5, then press the SET/TRACKING + or - button to select the CANCEL. Press the MENU button repeatedly to return to the normal screen. • After setting the ON TIMER, " " of the OFF TIMER will flash on and off. If you wish to set the OFF TIMER, press the ENTER button then follow the steps 4-6 on " TO SET THE OFF TIMER" . • If you want to correct the digits while setting, press the CANCEL button until the item you want to correct, then press the SET/TRACKING + or - button to correct the desired setting.