Panasonic SAAK320 SAAK320 User Guide - Page 13
MARKING A TRACK, RADIO, How discs with MP3 differ from CDs
View all Panasonic SAAK320 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
How discs with MP3 differ from CDs Marking a track You can mark one track each on the discs loaded so that you can start play from them later. To mark a track number 1 During play or stop Select your desired track. (For MP3, refer to "Track skip play" on page 10. For CD-DA, press the numbered buttons on the remote control. To select track 10 or over, press [X10] then the two digits.) 2 On the remote control Hold down [MARKER] until "STORING" blinks on the display. On the main unit AK520 AK523 Hold down [MARKER, -MEMORY] until "STORING" blinks on the display. The selected track is stored in the marker of the current disc. Note If a track is already stored in the marker, it will be replaced next time you store a new track in the same marker. To recall a marked track number in the current disc During play or stop On the remote control Press [MARKER] to recall a marker. On the main unit AK520 AK523 Press [MARKER, -RECALL] to recall a marker. Play starts from the track recalled. Note • "NO MARKER" indicates that the marker in the current disc is empty. • The marker memory is cleared when you open the CD tray. • For CD-DA, you cannot use this function during 1-RANDOM play and A-RANDOM play. • You cannot use this function during program mode. Radio Manual tuning 1 Press [TUNER, BAND] to select band. The unit comes on. Every time you press the button: FM ↔ AM 2 Press [PLAY MODE] on the remote control to select "MANUAL". Every time you press the button: MANUAL ↔ PRESET 3 Hold down [g/REW/3] or [f/FF/4] for a moment to search for a station. The frequency stops when it finds a clear station. To stop during the process, press [g/REW/3] or [f/FF/4]. Under excessive interference, a station may not be found. Press [g/REW/3] or [f/FF/4] repeatedly to tune step-bystep. "TUNED" is displayed when a radio station is tuned. "ST" is displayed when a stereo FM broadcast is being received. If noise is excessive in FM Remote control only Hold down [PLAY MODE] to display "MONO". Monaural sound is selected and noise reduces when reception is weak. Hold down [PLAY MODE] again to cancel the mode. "MONO" is also cancelled if the frequency is changed. Radio To receive FM broadcasts allocated in 0.1 MHz steps Main unit only Hold down [TUNER, BAND]. The display changes in a few seconds to show the current minimum FM frequency. Continue to hold down the button until the minimum frequency changes. The step is changed. Repeat the above to change the step back. Note • After changing the "allocation" setting, the frequencies you previously preset in the memory will be cleared. • Sound is momentarily interrupted if you load/unload tapes while listening to an AM broadcast. Preset tuning Remote control only There are two methods of pre-setting stations. Automatic presetting : All the stations the tuner can receive are preset. Manual presetting : You can select the stations to preset and the order they are preset in. Up to 15 stations each can be set in the FM and AM bands. Preparation: Press [TUNER, BAND] to select "FM" or "AM". Automatic presetting Do the following once each for FM and AM. Preparation: Tune to the frequency where pre-setting is to begin. Hold down [PROGRAM] until the frequency changes. The tuner presets all the stations it can receive into the channels in ascending order. When finished, the last station memorized is tuned in. AK520 AK523 AK320 AK323 Manual presetting Pre-set the stations one at a time. 1 Press [PROGRAM] then press [g, REW/3] or [f, 4/FF] to tune to the desired station. 2 Press [PROGRAM] then press [g, REW/3] or [f, 4/FF] to select a channel. 3 Press [PROGRAM]. The station occupying a channel is erased if another station is preset in that channel. Selecting channels Press the numbered buttons to select the channel. To enter channel 10 or over, press [>10], then the two digits. OR 1 Press [PLAY MODE] to select "PRESET". 2 Press [g, REW/3] or [f, 4/FF] to select the channel. 13 RQT7330