Panasonic SAHT700 SAHT690 User Guide - Page 27

The radio SELECTOR C.S.M PROGRESSIVE TUNING SELECTOR V.R.S M.R.S XTUNINGW VOLUME, DOWN, UP DOWN TUNE MODE FM MODE MEMORY DISC 1 2 3 4 5 VOLUME OPEN/CLOSE UP DISC EXCHANGE DISC SKIP TUNE MODE MEMORY FM MODE : 9 XCHW ENTER AV SYSTEM TV VCR DIGITAL TV/VIDEO AUX TUNER/BAND DVD/CD DISC PAGE GROUP SEQUENTIAL 1 DISC 1 4 DISC 4 7 REPEAT FL DISPLAY PLAY MODE CANCEL 2 DISC 2 5 DISC 5 8 3 DISC 3 6 9 S10/ENTER 0 SKIP SLOW/SEARCH CH TOP MENU DIRECT NAVIGATOR ENTER MENU PLAY LIST DISPLAY RETURN TV VOL s VOLUME TV VOL r SUBWOOFER S.POSITION C.FOCUS MIX 2CH LEVEL SFC S SRND PL TUNER/BAND Numbered buttons 6 5 VOLUME j i Manual tuning 1 Press [SELECTOR] to select "FM" or "AM". Each time you press the button: DVD/CD>FM>AM>TV>VCR>AUX>DIGITAL IN ([HT900]) Remote control: Press [TUNER/BAND]. 2 Press [TUNE MODE] to select "MANUAL". Each time you press the button: MANUAL()PRESET 3 Press [X TUNING] or [TUNING W] to select the frequency of the required station. ≥Remote control: Press [6] or [5]. TUNED: Displayed when a radio station is tuned. ST: Displayed when a stereo FM broadcast is being received. TUNEDST Press and hold [XTUNING] or [TUNINGW] until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found. 4 Adjust the volume. ∫ If noise is excessive in FM MONO Press [FM MODE] to display "MONO". Press [FM MODE] again to cancel the mode. The mode is also canceled when you changed the frequency. ∫ Allocation settings Each country allocates broadcast bands according to their particular system. [For\U.S.A.,\Canada,\and\units\with\PX\printed\on\the\outer\packaging] You can change the FM step. The step is factory-set to 0.2 MHz, but you can change it to receive broadcasts allocated 0.1-MHz steps. Radio operations [For\Latin\America] You can change the AM step. The step is factory-set to 9 kHz, but you can change it to receive broadcasts allocated 10-kHz steps. 1 Press [TUNER/BAND] to select "FM" (for either band). 2 Press and hold [SELECTOR] on the main unit. After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The minimum frequency changes and the step is changed. To return to the original step, repeat the above steps. [Note] Any FM/AM frequencies preset in channels will be changed by this procedure. Preset them again. Preset tuning Preset channels to make selection simple. Up to 15 stations can each be set in the FM and AM bands. Automatic presetting 1 Tune to "FM 87.9 MHz" or "FM 87.5 MHz" (➡ left). [For\Latin\America] Tune to "FM 87.50 MHz" (➡ left). 2 Press and hold [ENTER]. ≥Main unit: Press and hold [MEMORY]. Release the button when "FM AUTO" is displayed. The tuner presets all the stations it can receive into the channels in ascending order. "SET OK" is displayed when the stations are set. The last station to be set is then played. 3 Tune to "AM 520 kHz". [For\Latin\America] Tune to "AM 522 kHz" or "AM 520 kHz". 4 Press and hold [ENTER]. ≥Main unit: Press and hold [MEMORY]. ∫ "ERROR" is displayed Presetting was unsuccessful. Preset manually. Manual presetting 1 Tune to the station (➡ left). 2 Press [ENTER]. 3 While "PGM" is flashing Press the numbered buttons to select a channel. Alternatively, press [:, X CH] or [9, CH W] then press [ENTER]. The station occupying a channel is erased if another station is preset in that channel. Selecting channels 1 Press [TUNER/BAND] to select "FM" or "AM". 2 Press the numbered buttons or [:, X CH] or [9, CH W] to select the channel. To select a 2-digit number Example: To select channel 12, press [S10] ➡ [1] ➡ [2] RQT6750 27