Panasonic SC-HC200 Owners Manual - Page 12

Maintenance

Get Panasonic SC-HC200 PDF manuals and user guides View all Panasonic SC-HC200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

TQBJ2156 █ Main unit displays "--:--" • You connected the AC power supply cord for the first time or there was a power failure recently. Set the clock. "ADJUST CLOCK" • The clock is not set. Adjust the clock. "ADJUST TIMER" • The play timer is not set. Adjust the play timer. "AUTO OFF" • The system has not been used for 20 minutes and will turn off within a minute. To cancel, press any button. "ERROR" • An incorrect operation was done. Read the instructions and try again. "F61" "F77" • Disconnect the AC power supply cord and consult your dealer. "F703" • Examine the Bluetooth® connection. • Disconnect the Bluetooth® device. Turn off the system and then turn on again. "F76" • There is a problem with the power supply. • Disconnect the AC power supply cord and consult your dealer. "ILLEGAL OPEN" • The sliding door is not in a correct position. Turn off the system and then turn on again. "NO DEVICE" • The USB device is not connected. Examine the connection. "NO DISC" • You have not put in a disc. "NO PLAY" • Examine the content. You can only play supported format. • The files in the USB device may be corrupted. Format the USB device and try again. • The system may have a problem. Turn off the system and then turn on again. "PLAYERROR" • You played an unsupported MP3 file. The system will skip that track and play the next one. "LINKING" • This system is trying to connect to the last connected Bluetooth® device when "BLUETOOTH" is selected. "READING" • The unit is checking the "CD/USB" information. After this display has disappeared, start operating. "REMOTE 1" "REMOTE 2" • The remote control and the main unit are using different codes. Change the code of the remote control. - When "REMOTE 1" is shown, press and hold [OK] and [ ] for a minimum of 4 seconds. - When "REMOTE 2" is shown, press and hold [OK] and [USB/CD] for a minimum of 4 seconds. "SOUND 1 NOT SET" "SOUND 2 NOT SET" "SOUND 3 NOT SET" • You have not saved the sound effects into the sound setting number. 12 "USB OVER CURRENT ERROR" • The USB device is using too much power. Disconnect the USB device, turn off the system and then turn on again. • Check the connection, it may be caused by a faulty USB cable. "VBR" • The system cannot show the remaining play time for variable bit rate (VBR) tracks. "NOT SUPPORTED" • You have connected an unsupported USB device. Remote control code When other Panasonic equipment responds to the remote control of this system, change the remote control code for this system. Preparation Press [USB/CD] to select "CD". █ To set the code to "REMOTE 2" 1 Press and hold [8] on the main unit and [USB/CD] on the remote control. "REMOTE 2" is shown. 2 Press and hold [OK] and [USB/CD] for a minimum of 4 seconds. █ To set the code to "REMOTE 1" 1 Press and hold [8] on the main unit and [ ] on the remote control. "REMOTE 1" is shown. 2 Press and hold [OK] and [ ] for a minimum of 4 seconds. System memory reset Reset the memory when the following situations occur: • There is no response when buttons are pressed. • You want to clear and reset the memory contents. 1 Disconnect the AC power supply cord. 2 While you press and hold [1] on the main unit, connect the AC power supply cord again. Continue to press and hold the button until is shown. 3 Release [1]. All the settings are set back to the factory preset. It is necessary to set the memory items again. Maintenance Disconnect the AC power supply cord before maintenance. Clean this system with a soft, dry cloth. • Never use alcohol, paint thinner or benzine to clean this system. • Before using chemically treated cloth, read the instructions that came with the cloth carefully.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
12
TQBJ2156
█
Main unit displays
“--:--”
•
You connected the AC power supply cord for the first time or
there was a power failure recently. Set the clock.
“ADJUST CLOCK”
•
The clock is not set. Adjust the clock.
“ADJUST TIMER”
•
The play timer is not set. Adjust the play timer.
“AUTO OFF”
•
The system has not been used for 20 minutes and will turn
off within a minute. To cancel, press any button.
“ERROR”
•
An incorrect operation was done. Read the instructions and
try again.
“F61”
“F77”
•
Disconnect the AC power supply cord and consult your
dealer.
“F703”
•
Examine the Bluetooth
®
connection.
•
Disconnect the Bluetooth
®
device. Turn off the system and
then turn on again.
“F76”
•
There is a problem with the power supply.
•
Disconnect the AC power supply cord and consult your
dealer.
“ILLEGAL OPEN”
•
The sliding door is not in a correct position. Turn off the
system and then turn on again.
“NO DEVICE”
•
The USB device is not connected. Examine the connection.
“NO DISC”
•
You have not put in a disc.
“NO PLAY”
•
Examine the content. You can only play supported format.
•
The files in the USB device may be corrupted. Format the
USB device and try again.
•
The system may have a problem. Turn off the system and
then turn on again.
“PLAYERROR”
•
You played an unsupported MP3 file. The system will skip
that track and play the next one.
“LINKING”
•
This system is trying to connect to the last connected
Bluetooth
®
device when “BLUETOOTH” is selected.
“READING”
•
The unit is checking the “CD/USB” information. After this
display has disappeared, start operating.
“REMOTE 1”
“REMOTE 2”
•
The remote control and the main unit are using different
codes. Change the code of the remote control.
–
When “REMOTE 1” is shown, press and hold [OK] and
[
] for a minimum of 4 seconds.
–
When “REMOTE 2” is shown, press and hold [OK] and
[USB/CD] for a minimum of 4 seconds.
“SOUND 1 NOT SET”
“SOUND 2 NOT SET”
“SOUND 3 NOT SET”
•
You have not saved the sound effects into the sound setting
number.
“USB OVER CURRENT ERROR”
•
The USB device is using too much power. Disconnect the
USB device, turn off the system and then turn on again.
•
Check the connection, it may be caused by a faulty USB
cable.
“VBR”
•
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
“NOT SUPPORTED”
•
You have connected an unsupported USB device.
Remote control code
When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
Preparation
Press [USB/CD] to select “CD”.
█
To set the code to “REMOTE 2”
1
Press and hold [
8
] on the main unit and [USB/CD]
on the remote control.
“REMOTE 2” is shown.
2
Press and hold [OK] and [USB/CD] for a minimum
of 4 seconds.
█
To set the code to “REMOTE 1”
1
Press and hold [
8
] on the main unit and [
] on
the remote control.
“REMOTE 1” is shown.
2
Press and hold [OK] and [
] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
•
There is no response when buttons are pressed.
•
You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
2
While you press and hold [
1
] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button until
“– – – – – – – – –” is shown.
3
Release [
1
].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Maintenance
Disconnect the AC power supply cord before
maintenance. Clean this system with a soft, dry cloth.
•
Never use alcohol, paint thinner or benzine to clean this
system.
•
Before using chemically treated cloth, read the
instructions that came with the cloth carefully.