Panasonic SC-PM500 Owners Manual - Page 6

Placement of speakers, Making the connections, Preparing the remote control

Page 6 highlights

ENGLISH Preparing the remote control Placement of speakers Making the connections Conserving power The system consumes approximately 0.2 W when it is in standby mode. Disconnect the power supply if you do not use the system. Some settings will be lost after you disconnect the system. You have to set them again. R6/LR6, AA RQT9539 Use alkaline or manganese battery. Install the battery so that the poles (+ and -) align with those in the remote control. Point the remote control at the remote control sensor (Z 7), away from obstacles, at a maximum range of 7 m (23 feet) directly in front of the main unit. CAUTION! • Do not break open or short-circuit the battery. • Do not charge the alkaline or manganese battery. • Do not use the battery if the cover has peeled off. • Do not heat or expose to flame. • Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with doors and windows closed. • Mishandling of battery can cause electrolyte leakage, which can cause a fire. • Remove the battery if you do not use the remote control for a long period of time. Keep in a cool, dark area. CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 6 6 The right and left speakers are the same. Use only the supplied speakers. The combination of the main unit and speakers give the best sound. You can cause damage to the system and decrease the sound quality if you use other speakers. Note: • Keep your speakers at least 10 mm (13/32″) away from the system for proper ventilation. • Put the speakers on a flat safe surface. • These speakers do not have magnetic shielding. Do not put them near TVs, PCs or other equipment easily influenced by magnetism. • When you play at high levels for a long period, it can cause damage to the system and decrease the life of the system. • Decrease the volume in these conditions to prevent damage: - When you play distorted sound. - When you adjust the sound quality. • To prevent damage to the speakers, do not touch the speaker cones if you remove the nets. CAUTION! • Use the speakers only with the recommended system. If not, you can cause damage to the amplifier and speakers and can cause a fire. Consult an approved service personnel if damage occurs or if there is a sudden apparent change in performance. • Do the procedures included in these instructions when you attach the speakers. 1 4 B A (6:) (6:) 23 B A Black Red To household AC outlet Click! 1 Connect the speakers. Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers. 2 Connect the FM indoor antenna. Place the antenna where reception is best. 3 Connect the AM loop antenna. 4 Connect the AC power supply cord. Use the included AC power supply cord with this system only. Do not use an AC power supply cord from other equipment. PM500_PC1_1us.indd 6 7/14/2011 12:13:02 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

ENGLISH
ENGLISH
RQT9539
6
6
Placement of speakers
The right and left speakers are the same.
Use only the supplied speakers.
The combination of the main unit and speakers give the
best sound.
You can cause damage to the system and decrease the
sound quality if you use other speakers.
Note:
• Keep your speakers at least 10 mm (
13
/
32
) away from the
system for proper ventilation.
• Put the speakers on a flat safe surface.
• These speakers do not have magnetic shielding. Do
not put them near TVs, PCs or other equipment easily
influenced by magnetism.
• When you play at high levels for a long period, it can
cause damage to the system and decrease the life of
the system.
• Decrease the volume in these conditions to prevent
damage:
– When you play distorted sound.
– When you adjust the sound quality.
• To prevent damage to the speakers, do not touch the
speaker cones if you remove the nets.
CAUTION!
Use the speakers only with the recommended
system. If not, you can cause damage to the
amplifier and speakers and can cause a fire.
Consult an approved service personnel if damage
occurs or if there is a sudden apparent change in
performance.
Do the procedures included in these instructions
when you attach the speakers.
Making the connections
Conserving power
The system consumes approximately 0.2 W when it is in
standby mode. Disconnect the power supply if you do not
use the system.
Some settings will be lost after you disconnect the system.
You have to set them again.
2
3
B
4
(6
:
)
(6
:
)
A
A
1
B
To household
AC outlet
Red
Black
Click!
1
Connect the speakers.
Be careful not to cross
(short-circuit) or reverse the
polarity of the speaker wires
as doing so may damage the
speakers.
2
Connect the FM indoor antenna.
Place the antenna where reception is best.
3
Connect the AM loop antenna.
4
Connect the AC power supply cord.
Use the included AC power supply cord with this
system only.
Do not use an AC power supply cord from other
equipment.
Preparing the remote control
R6/LR6, AA
Use alkaline or manganese battery.
Install the battery so that the poles (+ and –) align with
those in the remote control.
Point the remote control at the remote control sensor
(
Z
7), away from obstacles, at a maximum range of 7 m
(23 feet) directly in front of the main unit.
CAUTION!
• Do not break open or short-circuit the battery.
• Do not charge the alkaline or manganese battery.
• Do not use the battery if the cover has peeled off.
• Do not heat or expose to flame.
• Do not leave the battery(ies) in an automobile exposed
to direct sunlight for a long period of time with doors and
windows closed.
• Mishandling of battery can cause electrolyte leakage,
which can cause a fire.
• Remove the battery if you do not use the remote control
for a long period of time. Keep in a cool, dark area.
CAUTION!
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
PM500_PC1_1us.indd 6
PM500_PC1_1us.indd
6
7/14/2011 12:13:02 PM
7/14/2011
12:13:02 PM