Panasonic SC-PMX100 Owners Manual - Page 17

IP/MAC Address To check this system's IP address or the Wi-Fi MAC address. 1 Press [RADIO, EXT-IN] repeatedly to select "Network". 2 Press [SETUP] repeatedly to select "Net Info" and then press [OK]. 3 Press [3, 4] to select "IP Addr." or "MAC Addr." and then press [OK]. The IP address or the MAC address is partially displayed. 4 Press [2, 1] on the remote control to show the rest of the IP address or the MAC address. • Press [OK] to exit. • The " - " displayed on the top or bottom left of the display indicate the first and last units respectively. Network reset To reset the network settings. 1 Press [RADIO, EXT-IN] repeatedly to select "Network". 2 Press [SETUP] repeatedly to select "Net Reset" and then press [OK]. 3 Press [2, 1] to select "OK? Yes" and then press [OK]. • Wait for "Network Initializing" to stop scrolling. • "WAC Mode" will be indicated on the display. - "Method 1" of network setting method is available. (> 6) - To exit "WAC Mode", press [∫]. • This function does not affect the "Wireless LAN" setting. Troubleshooting Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated do not solve the problem, consult your dealer for instructions. Do you have the latest software installed? Panasonic is constantly improving the system's software to ensure that our customers are enjoying the latest technology. (> 16) For further dedicated help, support and advice about your product please visit: http://panasonic.jp/support/global/cs/audio/ (This site is in English only.) Common problems Cannot turn on the unit. • After connecting the AC power supply cord, wait about 10 seconds before turning on the unit. No operations can be done with the remote control. • Examine that the battery is installed correctly. Sound is distorted or no sound. • Adjust the volume of the system. • Switch off the system, determine and correct the cause, then switch the system on again. It can be caused by straining of the speakers through excessive volume or power, and when using the system in a hot environment. • Ensure the speaker cables are connected correctly and securely. (> 4) A "humming" sound can be heard during playback. • An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords away from the cables of this system. The unit does not work. • One of the unit's safety devices may have been activated. Reset the unit as follows: 1 Press [Í/I] on the unit to switch the unit to standby. • If the unit does not switch to standby, press [Í/I] on the unit for approximately 10 seconds. The unit is forcibly switched to standby. Alternatively, disconnect the AC power supply cord, wait for at least 3 minutes, then reconnect it. 2 Press [Í/I] on the unit to switch it on. If the unit still cannot be operated, consult the dealer. Noise is heard. • During "AUX" mode, when a device is connected to both the AUX IN terminals and the USB port, noise may be generated depending on the device. In this case, remove the USB cable from the USB port. Disc Display not shown correctly. Playback does not start. • You have not put in the disc correctly. Put it in correctly. • Disc is dirty. Clean the disc. • Replace the disc if it is scratched, warped, or non-standard. • There is condensation. Let the system dry for 1 to 2 hours. Radio Reception is poor or a beat sound is heard. • Keep the antenna away from computers, TVs, other cables and cords. • Use an outdoor antenna. • Switch off the TV or move it away from the system. If noise is excessive during FM reception. • Change the audio to be output as monaural. 1 Press [RADIO MENU] repeatedly to select "FM Mode". 2 Press [2, 1] to select "Mono" and then press [OK]. The sound becomes monaural. • To cancel, select "Stereo" or change the frequency. In normal circumstances, select "Stereo". Stations cannot be selected. • Change the FM frequency step. 1 Press [SELECTOR] repeatedly to select "FM". 2 Press and hold [SELECTOR] on the unit. • After a few seconds the display changes to show the current lowest frequency. Continue to hold the button down. The lowest frequency changes and the step is changed. iPhone/iPad/iPod Cannot charge or operate. • Check that the iPhone/iPad/iPod is connected properly. • Connect the iPhone/iPad/iPod again or try to restart the iPhone/iPad/iPod. • During standby mode, charging will not start from the USB cable connection. Turn this unit on and make sure the charging has started before turning this unit to standby mode. • The battery of the iPhone/iPad/iPod is depleted. Charge the iPhone/iPad/iPod, and then operate again. - When using the port, turn this unit on. Do not turn this unit off until the iPhone/iPad/iPod becomes operational. 17 RQT9991