Panasonic SC-PMX100 Owners Manual - Page 6

RQT9991 Network settings You can stream music from an iOS device (iPhone/iPad/ iPod), an Android™ device or a PC (Mac/Windows) to this system's speakers by using the Qualcomm® AllPlay™ smart media platform, DLNA feature, or AirPlay. To use these features, this system must join the same network as the compatible device. Qualcomm® AllPlay™ smart media platform is a product of Qualcomm Connected Experiences, Inc. • Please update the system's software after the network settings are complete. (> 16) Choose a network setting method from the following. Wireless LAN connection Method 1: "Using the WAC (Wireless Accessory Configuration)" (> right) • If you are using an iPhone/iPad/iPod touch (iOS version 7.0 or later), or Mac (OS X 10.9 or later, with AirPort Utility 6.3.1 or later), you can sent its Wi-Fi configuration to this system. Method 2: "Using an Internet browser" (> right) • You can access this unit's network settings from the Internet browser on your smartphone or PC, etc. Method 3: "Using WPS (Wi-Fi Protected Setup™)" (> 7) • If your wireless router supports WPS, you can set up a connection by either pressing the WPS button, or entering the WPS PIN code. Wired LAN connection Method 4: "Using a LAN cable" (> 8) • You can make a stable connection to the network with a LAN cable. 6 Note: • The setting will be canceled after the set time limit. In that case, try the setting again. To cancel this setting in the middle, press [∫]. Wireless LAN connection This system has built-in Wi-Fi® and can be connected to a wireless router. Preparation • Place this system as close to the wireless router as possible. • Do not connect a LAN cable. Doing so will disable the Wi-Fi® function. • Point the antenna on the rear of the main unit up as shown in the figure. • Do not perform the following: - Tilting the antenna forward or backwards when it is pointing up - Applying too much force to the antenna - Carrying this unit by holding the antenna 1 Turn this system on. 2 Proceed to "Method 1", "Method 2" or "Method 3". Method 1: Using the WAC (Wireless Accessory Configuration) • The following explanations are based on an iPhone. 1 Connect the iPhone to your home wireless network. 2 Press [RADIO, EXT-IN] on the remote control repeatedly to select "Network". • When "WAC Mode" is indicated on the display, proceed to step 3. - If the display stays at "Network", perform the operation for network reset. (> 17) 3 Go to Wi-Fi settings on your iPhone. Settings Wi-Fi settings 4 Select "Panasonic PMX100 under the "SET UP NEW AIRPLAY SPEAKER stands for a character that is unique to each set. 5 The "AirPlay Setup" screen appears on your iPhone. • This system will be displayed as "Panasonic PMX100"*. * To change the name, enter a new name to replace the existing one. You can also do the renaming after the network connection is set up. (> 8, "To make network-related settings") • You can set a password for this system under "SPEAKER PASSWORD". (You will need this password if you make network settings by Internet browser next time.) 6 Select "Next" to apply the settings. • On the main unit's display, "Success" appears when the connection is established. (" " will be displayed.) Method 2: Using an Internet browser • The following explanations are based on a smartphone. 1 Press [RADIO, EXT-IN] on the remote control repeatedly to select "Network". 2 Press [SETUP] on the remote control repeatedly to select "Net Setup" and then press [OK]. 3 Press [3, 4] on the remote control to select "Manual" and then press [OK]. 4 Press [2, 1] on the remote control to select "OK? Yes" and then press [OK]. • After pressing [OK] to confirm "OK? Yes", the previous network connection you have set with this unit will be cleared. "Setting" blinks on the display. 5 Go to Wi-Fi settings on your compatible device. Settings Wi-Fi settings