Panasonic SCBTT770 SCBTT270 User Guide - Page 21
Reprogramming the remote control, When you experience problems, with settings
UPC - 885170029842
View all Panasonic SCBTT770 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
Getting started When you experience problems with settings Wireless Setting Wireless Settings Failed to complete. A conflict with another device occurred. Do you want to configure wireless network connection setting again ? Network Easy Setting (Internet Connection Check) Network Easy Setting (Internet Connection Check) Complete. - Connection to the Internet : Fail(Error code: B019) Failed the connection test. Cannot find the server.(Error code: B019) Please refer to the owner's manual for the cause of the error and the solution for it. Press [OK]. OK Yes No OK Display A conflict with another device occurred. A time out error occurred. An authentication error or a time out error occurred. A device error occurred. Check the following ≥ Please wait a few moments, and then try again. ≥ Setting of the Wireless router for MAC Address etc. ≥ The signal may be weak. ≥ The SSID ( right) and the encryption key of the Wireless router. ≥ Please wait a few moments, and then try again. ≥ Contact our Customer Service Center or your nearest dealer. Network Easy Setting (Home Network Connection Check) Network Easy Setting (Home Network Connection Check) Complete. 1. LAN cable connection 2. IP address setting 3. Connection to gateway : Fail : Fail : Fail LAN cable is not connected. Please check the connection. Select "Yes" and press [OK] to check network connection again. Select "No" and press [OK] to finish Network Easy Setting. Yes No OK Display Cannot find the server. (Error code: B019) Failed to connect to the server. (Error code: B020) Check the following ≥ "Primary DNS" and "Secondary DNS" Settings of "IP Address / DNS Settings" ( 40) ≥ The server may be busy or the service may have been suspended. Please wait a few moments, and then try again. ≥ Settings of "Proxy Server Settings" ( 40) and the router. ≥ Refer to the operating instructions of the hub or router. ≥ WPS (Wi-Fi Protected Setup) is a standard that facilitates settings relating to the connection and security of wireless LAN devices. To see whether your Wireless router supports WPS, check the Wireless router operating instructions. ≥ You can perform this setup anytime by selecting "Network Easy Setting" in the Setup menu. ( 40) ≥ You can redo these settings individually using "Network Settings". ( 40) ≥ Do not use this unit to connect to any wireless network for which you do not have usage rights. During automatic searches in a wireless network environment, wireless networks (SSID*) for which you do not have usage rights may be displayed; however, using these networks may be regarded as illegal access. ≥ After performing network settings on this unit, the settings (encryption level, etc.) of the Wireless router might change. When you have trouble getting online on your PC, perform the network settings on your PC in accordance with the settings of Wireless router. ≥ Please be aware that connecting to a network without encryption may result in the content of the communication being illegitimately viewed by a third party, or the leaking of data such as personal or secret information. * An SSID (Service Set IDentification) is a name used by wireless LAN to identify a particular network. Transmission is possible if the SSID matches for both devices. Display 1. LAN cable connection or Wireless setting 2. IP address setting 3. Connection to gateway 1. LAN cable connection or Wireless setting 2. IP address setting 3. Connection to gateway 1. LAN cable connection or Wireless setting 2. IP address setting 3. Connection to gateway :Fail :Fail :Fail :Pass :Fail :Fail :Pass :Pass :Fail Check the following ≥ Connection of the LAN cables ( 17) ≥ Connection and settings of the hub and router ≥ Settings of "IP Address / DNS Settings" ( 40) Reprogramming the remote control If you have more than one Panasonic player/recorder and the remote control operates both products at once, you will need to change the remote control code on one product to prevent this occurrence. ( 40, "Remote Control Code") VQT3D27 21