Panasonic TH-55LFE8U Professional Display for Simple Entry-Level Digital Signage - Page 55

Page 55 highlights

Network settings Set when networking with a computer. [Network settings] submenu will be displayed. Network settings Network control Display name LAN setup Network status AMX D.D. Crestron Connected™ Off LFE8-00 Off Off Reset Ŷ [Network control] Set when controlling with the unit's LAN terminal. [On]: Controls via LAN using the LAN terminal of the Display. The power indicator lights orange when the power is turned off with the remote control (standby). [Off]: Invalidates control with LAN terminal. (In this case, the power consumption of Standby condition (when the power is turned off with the remote control) will be slightly reduced.) Note Ɣ When using the LAN control function for "Using Network Function" (page 64-72), set this function to [On]. Ŷ [Display name] The name of the Display that is shown on the network can be changed. Ŷ [LAN setup] Detailed network settings for the LAN established via the LAN terminal of the Display or twisted pair cable transmitter can be configured. Select [LAN setup] with and press . LAN setup Save DHCP IP address Subnet mask Gateway Off 192.168. 0. 8 255.255.255. 0 192.168. 0. 1 Port 1024 [DHCP], [IP address], [Subnet mask], [Gateway] Press to set [On] / [Off] of [DHCP] and press . When [Off] is selected, IP address and other settings can be set manually. [DHCP]: (DHCP client function) [On]: Obtains an IP address automatically when a DHCP server exists in the network the Display is going to be connected. [Off]: When a DHCP server does not exist in the network the Display is going to be connected, set [IP address], [Subnet mask] and [Gateway] manually. [IP address]: (IP address display and setting) Enter an IP address when DHCP server is not used. [Subnet mask]: (Subnet mask display and setting) Enter a Subnet mask when DHCP server is not used. [Gateway]: (Gateway address display and setting) Enter a gateway address when DHCP server is not used. Note Ɣ When [DHCP] is set to [On], the IP address, etc. will be displayed in gray. Entering numbers *1BEESFTT I192.168. 0. 8 1. Select the address and press . 2. Select digits with . 3. Change numbers with . 4. Press . You can cancel the change by pressing . Select [Save] and press . Save the current network Setup. Note Ɣ To use a DHCP server, make sure the DHCP server is started. Ɣ Contact your network administrator for details on [IP address], [Subnet mask] and [Gateway]. Ɣ Shipping condition [DHCP]: Off [IP address]: 192.168.0.8 [Subnet mask]: 255.255.255.0 [Gateway]: 192.168.0.1 [Port] Set the port number used for command control. Select [Port] and press to set the number. Ɣ The available setting range is 1024 - 65535. Ɣ Entering numbers (see page 55) English 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
55
English
Network settings
Set when networking with a computer.
[Network settings] submenu will be displayed.
Ŷ
[Network control]
Set when controlling with the unit’s LAN terminal.
[On]:
Controls via LAN using the LAN terminal of the
Display. The power indicator lights orange when
the power is turned off with the remote control
(standby).
[Off]:
Invalidates control with LAN terminal.
(In this case, the power consumption of Standby
condition (when the power is turned off with the
remote control) will be slightly reduced.)
Note
Ɣ
When using the LAN control function for “Using
Network Function” (page 64-72), set this function
to [On].
Ŷ
[Display name]
The name of the Display that is shown on the network
can be changed.
Ŷ
[LAN setup]
Detailed network settings for the LAN established via
the LAN terminal of the Display or twisted pair cable
transmitter can be configured.
Select [LAN setup] with
and press <ENTER>.
192.168.
0.
8
255.255.255.
0
192.168.
0.
1
1024
LAN setup
Save
DHCP
Off
IP address
Subnet mask
Gateway
Port
[DHCP], [IP address], [Subnet mask], [Gateway]
Press
to set [On] / [Off] of [DHCP] and press
<ENTER>.
When [Off] is selected, IP address and other settings
can be set manually.
[DHCP]:
(DHCP client function)
[On]:
Obtains an IP address automatically when a
DHCP server exists in the network the Display is
going to be connected.
[Off]:
When a DHCP server does not exist in the
network the Display is going to be connected,
set [IP address], [Subnet mask] and [Gateway]
manually.
[IP address]:
(IP address display and setting)
Enter an IP address when DHCP server is not used.
[Subnet mask]:
(Subnet mask display and setting)
Enter a Subnet mask when DHCP server is not
used.
[Gateway]:
(Gateway address display and setting)
Enter a gateway address when DHCP server is not
used.
Note
Ɣ
When [DHCP] is set to [On], the IP address, etc. will
be displayed in gray.
Entering numbers
I
1
92.168.
0.
8
IP address
1.
Select the address and press <ENTER>.
2.
Select digits with
.
3. Change numbers with
.
4.
Press <ENTER>.
You can cancel the change by pressing
<RETURN>.
Select [Save] and press <ENTER>.
Save the current network Setup.
Note
ズ
To use a DHCP server, make sure the DHCP server
is started.
ズ
Contact your network administrator for details on [IP
address], [Subnet mask] and [Gateway].
ズ
Shipping condition
[DHCP]: Off
[IP address]: 192.168.0.8
[Subnet mask]: 255.255.255.0
[Gateway]: 192.168.0.1
[Port]
Set the port number used for command control.
Select [Port] and press <ENTER> to set the number.
ズ
The available setting range is 1024 - 65535.
ズ
Entering numbers (see page 55)
Network settings
Network control
LFE8-00
Off
Off
Off
Display name
Network status
LAN setup
AMX D.D.
Crestron Connected™
Reset