Panasonic WVCU360C WVCU360C User Guide - Page 19

Administrator Authorization, Baud Rate, Parity, Wait Time, Controller Unit-Group Address

Get Panasonic WVCU360C - SYSTEM CONTROLLER PDF manuals and user guides
UPC - 791871503454
View all Panasonic WVCU360C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

q Administrator Authorization 1. Press the CAM/SET button while [SEtUP] is displayed. The prompt appears. 2. Enter a password with the numeric buttons, then press the CAM/SET button. The default setting is [12345]. 3. [SPEED] appears when the right password is entered. If password entry failed, the menu returns to Notes: • We recommend that you register a new password different from "12345" in [SUSrP], and note down the registered password for future reference. • Powering up the controller while holding down numeric buttons 2, 4 and 5 simultaneously will reset the password to "12345". Remember that this procedure also resets all other menu parameters to the default settings. q Baud Rate In this menu, the communication speed (bps: bits per second) is selected. The communication speed should match that of the other units connected in the communication chain. 1. Display [SPEED] and press the CAM/SET button twice. 2. Select a parameter entering a bracket-enclosed number, e.g., (3), moving the joystick right and left, or pressing the [+] and [-] button. The default setting is 19 200 bps. (1) 2 400: 2 400 bps (2) 4 800: 4 800 bps (3) 9 600: 9 600 bps (4) 19 200: 19 200 bps Note: Selecting a slower rate (e.g., 2 400 bps) will delay the response time (e.g., the time until an activated alarm is reset). 3. Press the CAM/SET button to validate the selection. 4. Press the ESC button to go back to the previous menu. q Parity In this menu, the parity check mode is selected. 1. Display [PrtY] and press the CAM/SET button twice. 2. Select a parameter with the joystick. The default setting is None. n: None E: Even parity 3. Press the CAM/SET button to validate the selection. 4. Press the ESC button to go back to the previous menu. q Wait Time In this menu a wait time is selected. The controller will retransmit data when there is no response during the specified wait time. 1. Display [LJAit] and press the CAM/SET button twice. 2. Select a parameter with the joystick. The default setting is Off. (1) OFF: Off, no retransmission of data (2) 100: 100 ms (3) 200: 200 ms (4) 400: 400 ms (5) 500: 500 ms (6) 1 000: 1 s 3. Press the CAM/SET button to validate the selection. 4. Press the ESC button to go back to the previous menu. The following two menus should be maintained in the default condition. q Controller Unit-Group Address [CU-gr] appears on the Setup menu, but leave the default as it is. q System Unit-Group Address [SU-gr] appears on the Setup menu, but leave the default as it is. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
19
●
Administrator Authorization
1. Press the CAM/SET button while [SEtUP] is displayed.
The [- - - - -] prompt appears.
2. Enter a password with the numeric buttons, then press
the CAM/SET button.
The default setting is [12345].
3.
[SPEED] appears when the right password is entered. If
password entry failed, the menu returns to [- - - - -].
Notes:
• We recommend that you register a new password dif-
ferent from “12345” in [SUSrP], and note down the reg-
istered password for future reference.
• Powering up the controller while holding down numeric
buttons 2, 4 and 5 simultaneously will reset the pass-
word to “12345”. Remember that this procedure also
resets all other menu parameters to the default settings.
●
Baud Rate
In this menu, the communication speed (bps: bits per sec-
ond) is selected.
The communication speed should match
that of the other units connected in the communication
chain.
1.
Display [SPEED] and press the CAM/SET button twice.
2. Select a parameter entering a bracket-enclosed num-
ber, e.g., (3), moving the joystick right and left, or
pressing the [+] and [–] button.
The default setting is 19 200 bps.
(1) 2 400:
2 400 bps
(2) 4 800:
4 800 bps
(3) 9 600:
9 600 bps
(4) 19 200:
19 200 bps
Note:
Selecting a slower rate (e.g., 2 400 bps) will
delay the response time (e.g., the time until an acti-
vated alarm is reset).
3.
Press the CAM/SET button to validate the selection.
4.
Press the ESC button to go back to the previous menu.
●
Parity
In this menu, the parity check mode is selected.
1.
Display [PrtY] and press the CAM/SET button twice.
2.
Select a parameter with the joystick.
The default setting is None.
n:
None
E:
Even parity
3.
Press the CAM/SET button to validate the selection.
4.
Press the ESC button to go back to the previous menu.
●
Wait Time
In this menu a wait time is selected. The controller will
retransmit data when there is no response during the speci-
fied wait time.
1.
Display [LJAit] and press the CAM/SET button twice.
2.
Select a parameter with the joystick.
The default setting is Off.
(1) OFF:
Off, no retransmission of data
(2) 100:
100 ms
(3) 200:
200 ms
(4) 400:
400 ms
(5) 500:
500 ms
(6) 1 000:
1 s
3.
Press the CAM/SET button to validate the selection.
4.
Press the ESC button to go back to the previous menu.
The following two menus should be maintained in the
default condition.
●
Controller Unit-Group Address
[CU-gr] appears on the Setup menu, but leave the
default as it is.
●
System Unit-Group Address
[SU-gr] appears on the Setup menu, but leave the
default as it is.