Pentax 18836 Operation Manual - Page 149

Appendix, Problem, Cause, Remedy

Page 149 highlights

Problem Cause Remedy Subject is difficult to focus on with autofocus Lock focus on another object located at same distance (press shutter release button halfway), then aim at target and press shutter release button fully (p.37), or use Manual Focus mode. (p.69) Subject is not in focus Subject is not in focusing area Position subject in focus frame in middle of LCD monitor. If the subject is outside the focusing area, aim the camera at the subject and lock the focus (press shutter release button halfway), then compose picture and press the shutter release button fully. Subject is too close Set focus mode to q. (p.68) Focus mode is set to q Normal pictures will be out of focus if taken with focus mode set to q. Flash does not discharge Flash mode is set to a (flash off) Set to Auto or b (Flash On). (p.70) Drive mode is set to 1 Focus mode is set to s Flash will not discharge in these modes. Shooting mode is set to C or y USB connection with computer does not work properly USB connection mode Change the USB connection mode to is set to [PictBridge] [PC]. (p.134) USB connection with printer does not work properly USB connection mode Change the USB connection mode to is set to [PC] [PictBridge]. (p.115) Static electricity may occasionally prevent the camera from operating correctly. If this should occur, try removing and then reloading the batteries. If the camera turns on and operates properly, this indicates that there is no malfunction. You can use the camera as usual. 9 Appendix 147

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164

147
9
Appendix
Static electricity may occasionally prevent the camera from operating correctly. If this
should occur, try removing and then reloading the batteries. If the camera turns on and
operates properly, this indicates that there is no malfunction. You can use the camera
as usual.
Subject is not in
focus
Subject is difficult to
focus on with
autofocus
Lock focus on another object located at
same distance (press shutter release
button halfway), then aim at target and
press shutter release button fully (p.37),
or use Manual Focus mode. (p.69)
Subject is not in
focusing area
Position subject in focus frame in middle of
LCD monitor. If the subject is outside the
focusing area, aim the camera at the subject
and lock the focus (press shutter release
button halfway), then compose picture and
press the shutter release button fully.
Subject is too close
Set focus mode to
q
. (p.68)
Focus mode is set to
q
Normal pictures will be out of focus if
taken with focus mode set to
q
.
Flash does not
discharge
Flash mode is set to
a
(flash off)
Set to Auto or
b
(Flash On). (p.70)
Drive mode is set to
1
Focus mode is set to
s
Shooting mode is set
to
C
or
y
Flash will not discharge in these modes.
USB connection
with computer
does not work
properly
USB connection mode
is set to [PictBridge]
Change the USB connection mode to
[PC]. (p.134)
USB connection
with printer does
not work properly
USB connection mode
is set to [PC]
Change the USB connection mode to
[PictBridge]. (p.115)
Problem
Cause
Remedy