Pentax PC-300 PC-300 Manual - Page 5
Specifications, Databack, Operation
View all Pentax PC-300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
'33 5 7 -4, I I5:313 1'93 ® 0 & O ab SPECIFICATIONS Type: Film: Picture format: Film loading: Film movement: Frame number: Lens: Focusing system: Shutter: Self-timer: Viewfinder: Exposure: Flash: Charging time: Power source: Size and weight: 35mm lens-shutter camera 35 mm DX-coded film with ISO rating from 100 to 400; J135 cartridge. The camera film speed is automatically set to ISO 100 when non-DX film is used. 24 mm x 36 mm Auto film loading. Closing the back cover and pressing the shutter release button will automatically wind film to first exposure. Auto winding: auto rewinding starts at end of roll. (Rewind speed: approximately 22 sec for 24-exposure film.) Film can also be rewound in mid roll. Automatic readout of successive frame numbers in ascending order when shooting and descending order when rewinding. Pentax 35 mm, f/4.5, 3 elements in 3 groups Free focus. Focusing range : 1.5m (4.9ft.) to infinity. Programmed AE electronic shutter. Electronic lamp indication. Approx. 10-sec delay. Cancellation after activation is possible. Albada type bright frame finder Programmed auto-exposure Range: EV 10 - 15 (ISO 100) Built-in flash with automatic low-luminance firing. Approx. 6 sec according to Pentax testing conditions. Two 1 .5 V "AA" alkaline batteries. (Ni-Cd and maganese batteries are not usable.) 120 (W) x 70 (H) x 50 (D)mm ; approx. 185 g Date recording system: Date imprinting modes: Date imprinting power source: Size and weight: Information is recorded on the reverse side of the film. Push button to set unit to any of five modes; "Year/Mon/Day", "Day/Hour/Min Blank), "Mon/Day/Year" or "Day/Mon/Year". 3 V lithium battery (one CR2025 battery) 120 (W) x 70(H) x53 (D)mm ; approx. 200 g Reversal film (slide film) may not be properly exposed. Use of negative color film (print film) is recommended. DATABACK OPERATION, NOTE : THIS IS APPLICABLE TO THE PC 300 DATE MODEL ONLY. 0 Mode button 0 Select button 0 Adjust button 0 Battery cover fixing screw Changing the Mode Each time you press the Mode button 0 , the mode in the LCD panel changes in succession from (& "Year-Month-Day" to to ® "Day-Month-Year". ® "Day-Hour-Minute" to CO Stop pressing the button when " the desired " to C) "Month-Day-Year" mode appears. "----" indicates that no data will be imprinted on the picture. NOTE: "M" in the LCD panel indicates "Month". Use the adjuster pin on the strap to press the buttons. Correcting the Data 1. Press the "Select" button 0 until you reach the flickering digit which you wish to change. 2. Press the button 0 "Adjust" button 0 . Digits increase btyoocnheanegaechthetimdiegiyt oouf sppreecsisfietdheca"tAegdojurysty"oubucthtoonseOwi.thIfthyeou"Skeeleepcti"t depressed, the digit will advance continuously after two or three seconds. • 3. Adjusting the second: Press the "Select" button 0 until ":" will flicker. And press the "Adjust" 4. button After the in sync with a time correction, press the signal to "Select" set the second to button 0 to make zero. the data imprinting possible (the bar mark ( - ) appears on the LCD panel). Battery The databack is powered by one CR2025 3V Lithium battery. When the displays in the LCD cannot be by seen clearly or when the watch function loosening Battery cover fixing screw • . becomes When the unstable, replace the Battery with battery is set correctly, Data will be a new one displayed. Reset the data according to "Correcting the Data".