Pfaff quilt expression 4.0 Owner's Manual - Page 7

Presser feet - sewing machine

Get Pfaff quilt expression 4.0 PDF manuals and user guides View all Pfaff quilt expression 4.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Introduction Presser feet Standard presser foot 0A with IDT (attached on the machine upon delivery) This foot is used mainly for straight stitching and zigzag stitching with a stitch length longer than 1.0 mm. Fancy stitch foot 1A with IDT This foot is used for decorative stitches. The groove on the underside of the foot is designed to Áow smoothly over the stitches. Fancy stitch foot 2A When sewing decorative stitches or short zigzag stitches and other utility stitches with less than 1.0mm stitch length, use this foot. The groove on the underside of the foot is designed to Áow smoothly over the stitches. Blindhem foot 3 with IDT This foot is used for blindhem stitches. The toe on the foot guides the fabric. The red guide on the foot is designed to ride along the fold of the hem edge. Zipper foot 4 with IDT This foot can be snapped on either the right or the left of the needle, making it easy to sew close to both sides of the zipper teeth. Move the needle position to the right or left to sew closer to zipper teeth. Sensormatic buttonhole foot 5A When connected to the machine, the buttonhole is sewn in a suitable length to the button size that has been entered into the machine. Manual buttonhole foot 5M This foot is used for sewing manual buttonholes. Use the markings on the foot to position the garment edge. The Ànger on the back of the foot holds cording for corded buttonhole. Sensormatic free-motion foot 6A (4.0) This foot is used for sensormatic free-motion sewing. This foot can also be used for darning. Rolled hem foot 7 with IDT, 3 mm This foot is used to sew narrow hems in light to medium weight fabric. 1/4" quilting foot with IDT (4.0) This foot is perfect for piecing and patchwork, especially when used in conjunction with the straight stitch needle plate. The clearance between the needle and the outer edge of the toe is 1/4" (6 mm) and between the needle and the inner edge of the toe 1/8" (3 mm). Free-motion/Darning foot (3.0 and 2.0) Insert the pin of the foot as far as it will go into the hole at the back of the presser foot holder. The "C-shaped" guide should be positioned around the presser foot bar. The long arm must be behind the needle bar. Tighten the screw. Important: Make sure that the IDT is disengaged when using presser foot 2A, 5A, 5M, 6A and the free-motion/darning foot. 1:7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Introduction
Presser feet
Standard presser foot 0A with IDT (attached on the machine upon delivery)
This foot is used mainly for straight stitching and zigzag stitching with a stitch length
longer than 1.0 mm.
Fancy stitch foot 1A with IDT
This foot is used for decorative stitches. The groove on the underside of the foot is
designed to
Á
ow smoothly over the stitches.
Fancy stitch foot 2A
When sewing decorative stitches or short zigzag stitches and other utility stitches with
less than 1.0mm stitch length, use this foot. The groove on the underside of the foot is
designed to
Á
ow smoothly over the stitches.
Blindhem foot 3 with IDT
This foot is used for blindhem stitches. The toe on the foot guides the fabric. The red
guide on the foot is designed to ride along the fold of the hem edge.
Zipper foot 4 with IDT
This foot can be snapped on either the right or the left of the needle, making it easy to
sew close to both sides of the zipper teeth. Move the needle position to the right or left to
sew closer to zipper teeth.
Sensormatic buttonhole foot 5A
When connected to the machine, the buttonhole is sewn in a suitable length to the button
size that has been entered into the machine.
Manual buttonhole foot 5M
This foot is used for sewing manual buttonholes. Use the markings on the foot to position
the garment edge. The
À
nger on the back of the foot holds cording for corded buttonhole.
Sensormatic free-motion foot 6A (4.0)
This foot is used for sensormatic free-motion sewing. This foot can also be used for
darning.
Rolled hem foot 7 with IDT, 3 mm
This foot is used to sew narrow hems in light to medium weight fabric.
1/4” quilting foot with IDT (4.0)
This foot is perfect for piecing and patchwork, especially when used in conjunction with
the straight stitch needle plate. The clearance between the needle and the outer edge of
the toe is 1/4” (6 mm) and between the needle and the inner edge of the toe 1/8” (3 mm).
Free-motion/Darning foot (3.0 and 2.0)
Insert the pin of the foot as far as it will go into the hole at the back of the presser foot
holder. The ”C-shaped” guide should be positioned around the presser foot bar. The long
arm must be behind the needle bar. Tighten the screw.
Important: Make sure that the IDT is disengaged when using presser foot 2A, 5A, 5M, 6A and
the free-motion/darning foot.
1:7