Philips 20FT3010 User manual - Page 11

DFU 20FT3010/37 050404.0944 PRELIMINARY IFACE / HIFACE ITV Setup Menu Item Descriptions (continued) CURRENT RING* (1 / 2 / 3 / 4) SETUP x CONSUMER FEATURES MENU_ Determines which of the four channel rings is currently in effect. The current channel ring can also be selected by means of the RESET button on the setup remote (when the setup remote is in setup mode). Also see CHANNEL INSTALL. SWITCH ON CHANNEL* (STANDARD/AV1/ AV1YC/ AV2/AV2YC/CVI/TV 1-125) SETUP x CONSUMER FEATURES MENU_ Applicable to / available in Commercial Mode / setup menu only. If SWITCH ON CHANNEL is set to STANDARD, the channel to which the television will be adjusted at power-on will be the last channel / input to which it was tuned when the television was last powered off. If SWITCH ON CHANNEL is set to a particular input or channel, that will be the input or channel to which the television will be tuned at power-on. Note: AV1YC / AV2 / AV2YC are not applicable to the 20FT3010/37. POWER ON* (STANDARD / FORCED) SETUP x CONSUMER FEATURES MENU_ Applicable / available only to the Commercial Mode / setup menu. When POWER ON is set to FORCED, the television will automatically power-up whenever it is supplied with mains power. With POWER ON set to FORCED, the televi- sion will remain powered on long as mains power is applied, and cannot be turned off with a guest-mode remote, or with the television's keyboard (even if the keyboard is not locked out). When POWER ON is set to STANDARD, the television will remain in standby mode (i.e. off) when AC power is applied or resumed, until the unit is powered on. CHANNEL DISPLAY* (NUMBER / LABEL / ALL / NONE) SETUP x CONSUMER FEATURES MENU_ Applicable to / available in Commercial Mode / setup menu only. CHANNEL DISPLAY determines the channel information (NUMBER and / or LABEL), if any, that is displayed briefly whenever the channel is changed. Also see LABEL in CHANNEL INSTALLATION. Also see REMINDER KEYBOARD LOCK* (OFF / ON) SETUP x CONSUMER FEATURES MENU_ Applicable to / available in Commercial Mode / setup menu only. If KEYBOARD LOCK is set to ON, the television will not respond to commands from its local keyboard (power, channel, volume, etc.). When KEYBOARD LOCK is set to ON, the television responds to commands from its local keyboard (power, channel, volume, etc.) ESP* (OFF / 1 - 99) SETUP x CONSUMER FEATURES MENU_ Applicable / available only to the Commercial Mode / setup menu. ESP (Energy Savings Programmability), if not OFF, determines the number of hours (1 - 99) the television will remain powered on after the most recent front panel keyboard or remote control command. NOTE: If POWER ON (see POWER ON STANDARD / FORCED) is set to FORCED, E__S_P__h_a_s_n_o__e_ff_e_c_t WELCOME MESSAGE* (>) SETUP x CONSUMER FEATURES MENU_ Applicable / available only to the Commercial Mode / setup menu. The WELCOME MESSAGE feature makes it possible for an on-screen message to appear whenever the television is first turned on. The message will remain until any front- panel keyboard command or remote control command is received. The WELCOME MESSAGE sub-menu is shown below. WELCOME MESSAGE MESSAGE LINE 1 LINE 2 CLEAR EXIT OFF / ON (20 CHARACTERS) (20 CHARACTERS) > > Use cursor-up and cursor-down to select the WELCOME MESSAGE sub-menu item. While Line 1 or Line 2 of the WELCOME MESSAGE message is highlighted, use cursor-left and cursor-right to enter and exit message-edit mode and position the cursor within the line of the message content. Use cursor-up and cursor-down to change the character at the current position. Press RECALL on the Setup Remote to exit the editing mode and resume WELCOME MESSAGE sub-menu item selection. NOTE: WELCOME MESSAGE, when ON, overrides CHANNEL GUIDE at power-on, if the latter has been enabled. * COMMERCIAL FEATURE 11