Philips 60PP9202 User manual - Page 10
Onnecting A, Tandard, Layer - model
View all Philips 60PP9202 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Connecting Accessory Devices to Your TV CONNECTING A STANDARD DVD PLAYER Component video inputs allow the highest possible color and picture resolution in the playback of digital signals, such as those of DVD players. The color difference signals (Pb, Pr) and the luminance (Y) signal are connected and received separately. The result is better color bandwidth information than is possible with composite video (labeled VIDEO on your TV's jack panel) or S-Video connections. To make the connections shown in this example, you will need: • three cables for video connections (standard RCA connectors) • two cables for audio connections (standard RCA connectors). NOTE: The cables are not supplied with your TV. You should be able to buy them at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039. BEGIN 1 Connect the YPbPr (component) VIDEO OUT jacks from the DVD player to the INPUT-AV 1 YPbPr (component video) jacks on the rear of the TV. NOTE: The INPUT-AV 1 YPbPr jacks will accept 480i (interlaced) output signals only. The connection example on this page assumes the use of a DVD player with interlaced output. Some DVD players, however, have YPbPr outputs that can be switched between interlaced and progressive scan. If you are attempting to use a DVD player with progressive-scan (480p output) capability to make the connection shown in this example, you must be sure to switch the DVD player to interlaced. If necessary, refer to the DVD player's directions-for-use manual for help. If you want to use the DVD player in progressive-scan mode, you must use the HD INPUT-AV 4 jacks (see page 11). 2 Connect the AUDIO OUT L(eft) and R(ight) jacks from the DVD player to the INPUT-AV 1 AUDIO jacks on the rear of the TV. 3 Press the AV button on the remote control as many times as necessary to select the CVI (component video input) source on the TV. 4 Turn the DVD player on and press PLAY to view the DVD program on the TV. 2ANTENNA IN 75½ INPUT-AV 1 VIDEO S-VIDEO L L AUDIO R OUTPUT Y Pb Pr 1 INPUT-AV 2 VIDEO S-VIDEO L L AUDIO R Rear of TV HD INPUT-AV 4 G/Y R/Pr B/Pb V SYNC H L AUDIO R Rear of DVD Player* DIGITAL AUDIO OUT PCM-MPEG2-Dolby Digital-DTS COAXIAL OPT OUT SUB WF OUT 1 1 2 R L AUDIO OUT 2 (CVBS) VIDEO OUT PR/CR PB/CB Y VIDEO OUT (Y/C) S-VIDEO OUT *(Example: Philips DVD model DVD712) CVI POWER TV SWAP VCR PIP CH ACC ACTIVE CONTROL FREEZE DN UP SOUND PICTURE STATUS/ EXIT MENU/ SELECT MUTE VOL CH 3 123 456 789 TV/VCR A/CH 0 SURF SURF PIP ON/OFF REC • FORMAT SLEEP SAP AV DOLBY V PROG.LIST ITR/ RECORD HOME VIDEO HOME PERSONAL MOVIES POSITION PIP HELPFUL HINTS • To simplify making connections, the connectors on audio and video cables are often color coded. The jacks on your TV are likewise color coded to match the connectors. The coding is as follows: - Green for component video Y - Blue for the component video Pb - Red for the component video Pr - Red for the right audio channel - White for the left audio channel. • The names for the component video jacks may differ depending on the DVD player or accessory digital source equipment used. For example, besides YPbPr, you may see R-Y/B-Y/Y; or CrCbY. Although abbreviations and terms may vary, the letters B and R stand for the blue and red color component signal connectors, respectively, and Y indicates the luminance signal. If necessary, refer to the directions-foruse manual for your DVD or digital accessory for more information. • You can also connect a satellite receiver to the TV in a manner similar to the example shown on this page. If you connect a satellite receiver to the TV, you will need to use the receiver's channelmemorization system to store channels in the receiver's memory. • If you experience difficulties receiving sound with a DVD disc, check the sound settings through the DVD disc's menu. • The CVI signal source cannot be displayed in the PIP window. WARNING To prevent uneven picture-tube aging, do not leave nonmoving images or black borders on the screen for an extended period. See page 57. 10