Philips AC1213 User manual - Page 16

Cleaning the pre-filter

Get Philips AC1213 PDF manuals and user guides View all Philips AC1213 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Note •• If the air purifier is used in a dusty environment, it may need to be cleaned more often. •• If the humidity level in the room is very high, condensation may develop on the air quality sensor and the air quality light may indicate a more poor air quality even though the air quality is actually good. If this occurs, clean the air quality sensor or use the air purifier on a manual speed setting. 1 Switch off the air purifier and unplug from the wall outlet. 2 Clean the air quality sensor inlet and outlet with a soft brush (Fig.r). 3 Remove the air quality sensor cover (Fig.s). 4 Clean the air quality sensor, the dust inlet and the dust outlet with a damp cotton swab (Fig.t). 5 Dry all parts thoroughly with a dry cotton swab. 6 Reattach the air quality sensor cover (Fig.u). Note •• Always keep air quality cover closed while the air purifier is working. Cleaning the pre-filter Clean the pre-filter when F0 is displayed on the screen (Fig.v). 1 Switch off the air purifier and unplug from the wall outlet. 2 Pull the bottom part of the front panel and then gently lift to remove it from the air purifier (Fig.c). 3 Press the clip down (1) and pull the pre-filter towards you (2) (Fig.d). 4 If the pre-filter is very dirty, use a soft brush to brush away the dust. Then wash the pre-filter under running tap water (Fig.w). 5 Allow the pre-filter to air dry thoroughly before placing back in the air purifier. Note •• To optimize the lifetime of the prefilter, make sure it dries completely after cleaning. •• Wash your hands after handling the filter. 6 Put the pre-filter back into the air purifier (Fig.h). Note •• Make sure the side with the clip is pointing towards you, and that all hooks of the pre-filter are properly attached to the air purifier. 7 To reattach the front panel, press the top part of the panel onto the top of the air purifier (1). Then, gently push the panel against the body of the air purifier (2) (Fig.i). 8 Put the plug of the air purifier in the wall outlet. 9 Touch and hold the for 3 seconds to reset the pre-filter cleaning time (Fig.x). 10 Wash your hands thoroughly after installing filters. 14 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Note
•
If the air purifier is used in a dusty
environment, it may need to be
cleaned more often.
•
If the humidity level in the room is
very high, condensation may develop
on the air quality sensor and the air
quality light may indicate a more poor
air quality even though the air quality
is actually good. If this occurs, clean
the air quality sensor or use the air
purifier on a manual speed setting.
1
Switch off the air purifier and
unplug from the wall outlet.
2
Clean the air quality sensor inlet
and outlet with a soft brush (Fig.
r
).
3
Remove the air quality sensor cover
(Fig.
s
).
4
Clean the air quality sensor, the
dust inlet and the dust outlet with a
damp cotton swab (Fig.
t
).
5
Dry all parts thoroughly with a dry
cotton swab.
6
Reattach the air quality sensor
cover (Fig.
u
).
Note
•
Always keep air quality cover closed
while the air purifier is working.
Cleaning the pre-filter
Clean the pre-filter when
F0
is displayed
on the screen (Fig.
v
).
1
Switch off the air purifier and
unplug from the wall outlet.
2
Pull the bottom part of the front
panel and then gently lift to remove
it from the air purifier (Fig.
c
).
14
EN
3
Press the clip down (1) and pull the
pre-filter towards you (2) (Fig.
d
).
4
If the pre-filter is very dirty, use a
soft brush to brush away the dust.
Then wash the pre-filter under
running tap water (Fig.
w
).
5
Allow the pre-filter to air dry
thoroughly before placing back in
the air purifier.
Note
•
To optimize the lifetime of the pre-
filter, make sure it dries completely
after cleaning.
•
Wash your hands after handling the
filter.
6
Put the pre-filter back into the air
purifier (Fig.
h
).
Note
•
Make sure the side with the clip is
pointing towards you, and that all
hooks of the pre-filter are properly
attached to the air purifier.
7
To reattach the front panel, press
the top part of the panel onto the
top of the air purifier (1). Then,
gently push the panel against the
body of the air purifier (2) (Fig.
i
).
8
Put the plug of the air purifier in the
wall outlet.
9
Touch and hold the
for
3 seconds to reset the pre-filter
cleaning time (Fig.
x
).
10
Wash your hands thoroughly after
installing filters.