Philips MZ7C37L User manual - Page 23
Recording
View all Philips MZ7C37L manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
Notes: - For recording, use only tape of IEC type I (normal tape) or IEC type II (Cr02). - The tape is secured at both ends with leader tape. At the beginning and end of tape, nothing will be recorded for six to seven seconds. - The recording level is set automatically, regardless of the position of Volume, Incredible Surround or Bass/Treble. - To prevent accidental recording, break out the tab on the left shoulder of the tape side you want to protect. - If "CHECK TAPE" is displayed, the protection tab has been broken. Put a piece of clear adhesive tape over the opening. Do not cover the Cr02 tape detection hole when covering the tab opening. One Touch Recording • For One Touch Recording, as soon as you press REC, the current source (3 CDC, TUNER or CDR/AUX) will be recorded on tape deck 2 1 Load a blank tape in tape deck 2. 2 Press REC to start recording. ™ The REC flag starts flashing. 3 Press STOP to stop recording. Note: - When you press RECORD while in TAPE mode, "SELECT SOURCE" will be displayed. One Touch Recording is not possible in TAPE mode. Recording from other sources (only on tape deck 2) 1 Press TAPE to select tape deck 2. 2 Load a blank tape into tape deck 2 with the open side downward. 3 Press SIDE on remote control to select the recording side. ™ The BACK or FRONT flag will be displayed, depending on the side selected. 4 Press 3 CDC, TUNER or CDR/AUX. • Start playback of the selected source. 5 Press REC to start recording. ™ The REC flag starts flashing. 6 Press STOP to stop recording. Notes: - Only å or ç mode is available during recording. - During recording, it is not possible to listen to another source. Dubbing tapes (from tape deck 1 to tape deck 2) 1 Press TAPE to select tape deck 2. 2 Load the prerecorded tape into tape deck 1 and a blank tape into tape deck 2. • Make sure the tape in tape deck 1 has its full spool to the left. 3 (For Tape Deck 2 only) Press SIDE on the remote control to select the recording side. RECORDING 4 Press DUBBING NORMAL•FAST once for normal speed dubbing or twice (within 2 seconds) for high speed dubbing. ™ "NORMAL" (normal speed) or "FAST" (high speed) will be displayed, followed by "DUBBING". ™ The HSD flag appears on the display during high speed dubbing. • Dubbing will start immediately. ™ The REC flag starts flashing. 5 Press STOP to stop dubbing. Notes: - Only å mode is available during dubbing. - At the end of side A, flip the tapes to side B and repeat the procedure. - Dubbing of tapes is only possible from tape deck 1 to tape deck 2. - To ensure good dubbing, use tapes of the same length. - During high speed dubbing in Tape mode, the sound is reduced to a low volume. - You can listen to another source while dubbing. CD Synchro Start Recording During CD synchro start recording, • Do not fast forward/rewind your tape in tape deck 1. • Do not listen to another source. 1 Press TAPE to select tape deck 2. • Load a blank tape into tape deck 2 with the open side downward. 2 Press SIDE on remote control to select the recording side. 3 Press A. REV to select the playback mode ( å or ç ). 4 Press 3 CDC. • You can program the tracks in the order you want them to be recorded (see Programming Tracks). If you do not, the tracks are recorded according to the order on the selected disc. 5 Press CD SYN to start recording. ™ The REC flag starts flashing. 6 Press STOP to stop recording CD playback. Digital Recording via Digital Out For CD digital recording, please refer to the Instructions Manual of the CD Recorder, digital audio equipment, etc. 23 English