Pioneer AVM-P9000R Owner's Manual - Page 61

Adjustments for Speaker

Get Pioneer AVM-P9000R PDF manuals and user guides View all Pioneer AVM-P9000R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Adjusting Audio (Basic) 5. Cancel the FAD/BAL Setting Menu by clicking the joystick. Note: • "F 00" is the proper setting when 2 speakers are in use. Adjustments for Speaker You need to make "with/without" (or yes/no) and "size" (bass reproducing capacity) selection/adjustments depending on the installed speakers. The size needs to be set to Large if the speaker is capable of reproducing sounds of about 100 Hz or below. Otherwise select Small. 1. Select "SP Setting" by moving the joystick. "SP Setting" is highlighted in green. 2. Click the joystick. The Speaker Setting Menu appears. The Front Left speaker is highlighted in green and in the lower right-hand corner of the screen the current settings of that speaker is shown. Operation at the Speaker Setting Menu Center Front Left Rear Left Front Right Rear Right Sub Woofer Show the current settings of the selected speaker • To select a speaker, move the joystick up/down and left/right. You cannot move diagonally. : Move the joystick left/right. : Move the joystick up/down. Test Tone: See "Adjusting the Speakers' Output Levels using a Test Tone" (p. 68). Cross Over: See "Selecting a Crossover Frequency" (p. 69). SW Phase: See "Correcting the Subwoofer's Phase" (p. 69). Audio Setting: Select this to go to the Audio Setting Menu. Return: Completes operations at the Speaker Setting Menu, bringing you back to the previous screen. Continued overleaf. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
5.
Cancel the FAD/BAL Setting Menu by clicking the joystick.
Note:
•
“F 00” is the proper setting when 2 speakers are in use.
Adjustments for Speaker
You need to make “with/without” (or yes/no) and “size” (bass reproducing capacity) selec-
tion/adjustments depending on the installed speakers. The size needs to be set to Large if the
speaker is capable of reproducing sounds of about 100 Hz or below. Otherwise select Small.
1.
Select “SP Setting” by moving the joystick.
“SP Setting” is highlighted in green.
2.
Click the joystick.
The Speaker Setting Menu appears.
The Front Left speaker is highlighted in green and in
the lower right-hand corner of the screen the current
settings of that speaker is shown.
60
Continued overleaf.
Adjusting Audio (Basic)
Operation at the Speaker Setting Menu
•
To select a speaker, move the joystick up/down and
left/right. You cannot move diagonally.
:
Move the joystick left/right.
:
Move the joystick up/down.
Test Tone:
See “Adjusting the Speakers’ Output
Levels using a Test Tone” (p. 68).
Cross Over:
See “Selecting a Crossover Frequency” (p. 69).
SW Phase:
See “Correcting the Subwoofer’s Phase” (p. 69).
Audio Setting:
Select this to go to the Audio Setting Menu.
Return:
Completes operations at the Speaker Setting Menu, bringing you back to the
previous screen.
Center
Front Left
Rear Left
Sub Woofer
Front Right
Rear Right
Show the current settings
of the selected speaker