Pioneer C-72 Operating Instructions - Page 28
Specifications
View all Pioneer C-72 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 28 highlights
SPECIFICATIONS Amplifier Section Rated output 20 Hz- 20 kHz, 0.01 % 10 kg 7V Total harmonic distortion 20 Hz - 20 kHz, 1 V 0.002 % Input terminals (sensitivity/impedance) PHONO MM 2.5 mV/50 kU PHONO MC 250 µV/100 g CD, TUNER, TAPE PLAY, AUX 150 mV/50 Output terminals (output level/output impedance) TAPE REC 150 mV/2.2 kg PRE OUT 1 V/1 kg Frequency response PHONO MM 20 Hz - 20 kHz ±0.2 dB PHONO MC 20 Hz - 20 kHz ±0.3 dB CD, TUNER, TAPE PLAY, AUX, 1 Hz - 150 kHz ±3 dB Tone control (Volume control set at - 40 dB position) BASS + 8 dB, 100 Hz TREBLE ±8 dB, 10 kHz Filter SUBSONIC 17 Hz, - 12 dB/oct MUTING - co dB SN ratio (short-circuit, A network) PHONO MM 93 dB.(5 mV) PHONO MC 76 dB (500 µV) CD, TUNER, TAPE PLAY, AUX 106 dB Video section Video (Base Band) Input terminals (Output level/impedance) LD, VCR 1, 2, VIDEO, TV/AUX 1 Vp-p/75 52 unbalanced Output terminals (Output level/impedance) VCR 1, 2, REC MONITOR 1 Vp-p/75 g unbalanced DG 2 % DP 2° Frequency response 10 Hz - 10 MHz ±3 dB Noise level - 60 dB or less S type terminal Input terminal (luminance signals sensitivity/impedance, color signals sensitivity/impedance) LD, VCR 1, 2, VIDEO, TV/AUX 1 Vp-p/75 SZ unbalanced 0.286 Vp-p/7512 unbalanced Output terminal (luminance signals output level/impedance, color signals output level/impedance) VCR 1, 2, MONITOR 1 Vp-p/75 SZ unbalanced 0.286 Vp-p/75 g unbalanced Luminance signals frequency characteristic 10 Hz - 10 MHz -3 dB Noise level (luminance signal) max. -60 dB Power section, other Power requirements Power consumption AC outlets SWITCHED UNSWITCHED External dimensions Weight AC 120 V, 60 Hz 30 W TOTAL 900 W MAX TOTAL 100 W MAX 459 (W) x 417 (D) x 163 (H) mm 18-1/16 (W) x 16-7/16 (D) x 6-7/16 (H) in 11.3 kg (24 lb 15 oz) Accessories Remote control unit 1 Alkaline dry cell batteries (IEC LR03 (AM-41) 4 Templates added 2 Pin-plug cord 1 Cushion spacer 2 Operating Instructions 1 The specifications and design noted above are subject to change without notice, due to improvements. POWER-CORD CAUTION Handle the power cord by the plug. Do not pullout the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc,. on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. MAINTENANCE OF EXTERNAL SURFACES • Use a polishing cloth or dry cloth to wipe off dust and dirt. • When the surfaces are very dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleaners. • Never use thinners, benzene, insecticide sprays and other chemicals on or near this unit, since these will corrode the surfaces. Published by Pioneer Electronic Corporation. Copyright © 1990 Pioneer Electronic Corporation. All rights reserved. PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153, Japan PIONEER ELECTRONICS [USA] INC. 2265 East 220th Street, Long Beach, California 90810, U.S.A. P.O. BOX 1720, Long Beach, California 90801, U.S.A. PIONEER ELECTRONICS OF CANADA, INC. 505 Cochrane Drive, Markham, Ontario L3R 8E3, Canada PIONEER ELECTRONIC [EUROPE] N.V. Keetberglaan 1, 2740 Beveren, Belgium; TEL: 03/750.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 580-9911 Printed in Japan < ARB1268-A>