Pioneer CT-W208R Operating Instructions - Page 12

Playback Sequence With Rev Mode, Switch Setting, Relay Playback, O Stop Playback

Page 12 highlights

PLAYBACK RELAY PLAYBACK When relay playback mode is selected, continuous playback can be performed. When the tape in the first deck reaches its end and stops, the other deck will automatically begin playback. 1. Load prerecorded tapes in DECK I and DECK II. 2. Set the DOLBY NR switch. ÷ Always set the switch to the same positions that was used for recording. 3. Set the REV MODE switch to (See table entitled "PLAYBACK SEQUENCE WITH REV MODE SWITCH SETTING" on this page). 4. Set the stereo amplifier for tape playback. 5. Press the playback (3 or 2) button of the deck that will start to play first. ÷ When the tape in one deck ends, the other deck automatically begins playback. ÷ To cancel relay playback, press the stop (7) button. NOTES: ÷ Relay playback can begin from either DECK I or DECK II. ÷ The tape in the idle deck can be replaced during relay playback mode, allowing many tapes to be played back continuously. This is a convenient feature for parties, background music, etc. ÷ When this mode is selected, of the deck encounters an unrecorded portion of tape more than 15 seconds in length, it will fast forward the tape until it encounters another recorded portion, and resume playback from that point. To stop playback temporarily(Deck II only) Press the pause (8) button. ÷ To resume playback, either press the pause (8) button again, or press the playback (3 or 2) button. To stop playback Press the stop (7) button of the operating deck. PLAYBACK SEQUENCE WITH REV MODE SWITCH SETTING The playback sequence depends on the setting of the REV MODE switch and on which playback (3 or 2) button is pressed first. The playback sequence for each possible selection is shown below. *2 In the repeat ( ) mode, relay playback always begins from the forward direction. I # : DECK I forward playback I @ : DECK I reverse playback II # : DECK II forward playback II @ : DECK II reverse playback ∞ : Auto-reverse function = : Relay REV Starting Other MODE play- deck switch back mode button Playback sequence DECK I3 *2 DECK I2 *2 I# ∞I @=II # ∞II @=I # ∞I @... 15 times relay (32 sides playback) I@ = II #∞II @ = I #∞I @ = II #... 15 times relay (31 sides playback) DECK II3 *2 II# ∞II @=I #∞ I @=II # ∞II @... 15 times relay (32 sides playback) DECK II2 *2 II@ = I #∞I @ = II #∞II@ = I #... 15 times relay (31 sides playback) 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

12
PLAYBACK
REV
MODE
switch
Starting
play-
back
button
Playback sequence
15 times relay
(32 sides playback)
*2
*2
I
#
I
@=
II
#
II
@=
I
#
I
@
I
@ =
II
#
II
@ =
I
#
I
@ =
II
#
DECK I
3
DECK I
2
Other
deck
mode
15 times relay
(31 sides playback)
15 times relay
(32 sides playback)
15 times relay
(31 sides playback)
*2
*2
DECK II
2
DECK II
3
II
#
II
@=
I
#
I
@=
II
#
II
@
II
@ =
I
#
I
@ =
II
#
II
@ =
I
#
PLAYBACK SEQUENCE WITH REV MODE
SWITCH SETTING
The playback sequence depends on the setting of the
REV MODE switch and on which playback (
3
or
2
)
button is pressed first. The playback sequence for
each possible selection is shown below.
*2 In the repeat (
) mode, relay playback always
begins from the forward direction.
I
#
: DECK I forward playback
I
@
: DECK I reverse playback
II
#
: DECK II forward playback
II
@
: DECK II reverse playback
: Auto-reverse function
=
: Relay
RELAY PLAYBACK
When relay playback mode is selected, continuous
playback can be performed. When the tape in the
first deck reaches its end and stops, the other deck
will automatically begin playback.
1.
Load prerecorded tapes in DECK I and DECK II.
2.
Set the DOLBY NR switch.
÷
Always set the switch to the same positions
that was used for recording.
3.
Set the REV MODE switch to
(See table en-
titled "PLAYBACK SEQUENCE WITH REV MODE
SWITCH SETTING" on this page).
4.
Set the stereo amplifier for tape playback.
5.
Press the playback (
3
or
2
) button of the deck
that will start to play first.
÷
When the tape in one deck ends, the other
deck automatically begins playback.
÷
To cancel relay playback, press the stop (
7
)
button.
NOTES:
÷
Relay playback can begin from either DECK I or
DECK II.
÷
The tape in the idle deck can be replaced during relay
playback mode, allowing many tapes to be played
back continuously. This is a convenient feature for
parties, background music, etc.
÷
When this mode is selected, of the deck encounters
an unrecorded portion of tape more than 15 seconds
in length, it will fast forward the tape until it encoun-
ters another recorded portion, and resume playback
from that point.
To stop playback temporarily(Deck II only)
Press the pause (
8
) button.
÷
To resume playback, either press the pause (
8
)
button again, or press the playback (
3
or
2
) button.
T
o stop playback
Press the stop (
7
) button of the operating deck.