Pioneer DEH-P6000 Owner's Manual - Page 31

Adjusting the brightness, Setting the rear output and, subwoofer controller, Switching the sound,

Get Pioneer DEH-P6000 PDF manuals and user guides View all Pioneer DEH-P6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Initial Settings Section 04 Initial Settings ! For this function, verify the topic Adjusting initial settings before initiating the operation. 1 Display the intial setting menu. 2 Use MULTI-CONTROL to select Dimmer. 3 Press MULTI-CONTROL to turn dimmer on. # To turn dimmer off, press MULTI-CONTROL again. Adjusting the brightness You can adjust the display brightness. ! For this function, verify the topic Adjusting initial settings before initiating the operation. 1 Display the intial setting menu. 2 Use MULTI-CONTROL to select Brightness. 3 Push MULTI-CONTROL left or right to adjust the brightness level. 0 to 15 is displayed as the level is increased or decreased. # When dimmer is functioning, the brightness level can be adjusted 0 to 10. Setting the rear output and subwoofer controller This unit's rear output (rear speaker leads output and RCA rear output) can be used for fullrange speaker (Rear SP :F.Range) or subwoofer (Rear SP :S/W) connection. If you switch the rear output setting to Rear SP :S/W, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, the unit is set for rear full-range speaker connection (Rear SP :F.Range). ! For this function, verify the topic Adjusting initial settings before initiating the operation. 1 Display the intial setting menu. 2 Use MULTI-CONTROL to select S/W control. 3 Press MULTI-CONTROL to switch the rear output setting. Pressing MULTI-CONTROL will switch between Rear SP :F.Range (full-range speaker) and Rear SP :S/W (subwoofer) and that status will be displayed. # When no subwoofer is connected to the rear output, select Rear SP :F.Range. # When a subwoofer is connected to the rear output, set for subwoofer Rear SP :S/W. Notes ! Even if you change this setting, there is no output unless you turn the subwoofer output on (refer to Using subwoofer output on page 27). ! If you change this setting, subwoofer output in the audio menu return to the factory settings. ! Both rear speaker lead outputs and RCA rear output are switched simultaneously in this setting. Switching the sound muting/attenuation Sound from this system is muted or attenuated automatically when the signal from the equipment with mute function is received. ! The sound is muted or attenuated, MUTE or ATT are displayed and no audio adjustment is possible. ! Sound from this system returns to normal when the muting or attenuation is canceled. ! For this function, verify the topic Adjusting initial settings before initiating the operation. 1 Display the intial setting menu. 2 Use MULTI-CONTROL to select Mute. En 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
!
For this function, verify the topic
Adjusting
initial settings
before initiating the opera-
tion.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select Dimmer.
3
Press MULTI-CONTROL to turn dimmer
on.
#
To turn dimmer off, press
MULTI-CONTROL
again.
Adjusting the brightness
You can adjust the display brightness.
!
For this function, verify the topic
Adjusting
initial settings
before initiating the opera-
tion.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select
Brightness.
3
Push MULTI-CONTROL left or right to
adjust the brightness level.
0
to
15
is displayed as the level is increased or
decreased.
#
When dimmer is functioning, the brightness
level can be adjusted
0
to
10
.
Setting the rear output and
subwoofer controller
This unit
’
s rear output (rear speaker leads out-
put and RCA rear output) can be used for full-
range speaker (
Rear SP :F.Range
) or subwoo-
fer (
Rear SP :S/W
) connection. If you switch
the rear output setting to
Rear SP :S/W
, you
can connect a rear speaker lead directly to a
subwoofer without using an auxiliary amp.
Initially, the unit is set for rear full-range speak-
er connection (
Rear SP :F.Range
).
!
For this function, verify the topic
Adjusting
initial settings
before initiating the opera-
tion.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select
S/W control.
3
Press MULTI-CONTROL to switch the
rear output setting.
Pressing
MULTI-CONTROL
will switch be-
tween
Rear SP :F.Range
(full-range speaker)
and
Rear SP :S/W
(subwoofer) and that status
will be displayed.
#
When no subwoofer is connected to the rear
output, select
Rear SP :F.Range
.
#
When a subwoofer is connected to the rear
output, set for subwoofer
Rear SP :S/W
.
Notes
!
Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to
Using subwoofer output
on page
27).
!
If you change this setting, subwoofer output
in the audio menu return to the factory set-
tings.
!
Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this
setting.
Switching the sound
muting/attenuation
Sound from this system is muted or attenu-
ated automatically when the signal from the
equipment with mute function is received.
!
The sound is muted or attenuated,
MUTE
or
ATT
are displayed and no audio adjust-
ment is possible.
!
Sound from this system returns to normal
when the muting or attenuation is can-
celed.
!
For this function, verify the topic
Adjusting
initial settings
before initiating the opera-
tion.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select Mute.
Initial Settings
En
31
Section
04
Initial Settings