Pioneer DEH-P6500 Owner's Manual - Page 30

Adjusting loudness, Using subwoofer output, Using non fading output, Audio Adjustments

Get Pioneer DEH-P6500 PDF manuals and user guides View all Pioneer DEH-P6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Section HHHHHHHHHHHHHH 07 Audio Adjustments Adjusting loudness Loudness compensates for deficiencies in the low- and high-sound ranges at low volume. 1 Press AUDIO to select Loud. Press AUDIO until Loud appears in the display. 2 Press a to turn loudness on. Loudness level (e.g., Loud Mid) appears in the display. 3 Press c or d to select a desired level. Each press of c or d selects level in the following order: Low (low)Mid (mid)High (high) 4 Press b to turn loudness off. Loud OFF appears in the display. Using subwoofer output This unit is equipped with a subwoofer output which can be turned on or off. 1 Press AUDIO to select Sub-W1. Press AUDIO until Sub-W1 appears in the display. # When the subwoofer controller setting is PREOUT :FULL, you cannot select Sub-W1. 2 Press a to turn subwoofer output on. Sub-W1 Normal appears in the display. Subwoofer output is now on. # To turn subwoofer output off, press b. 3 Press c or d to select the phase of subwoofer output. Press c to select reverse phase and Rev. appears in the display. Press d to select normal phase and Normal appears in the display. Adjusting subwoofer settings When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Press AUDIO to select Sub-W2. Press AUDIO until Sub-W2 appears in the display. # When the subwoofer output is on, you can select Sub-W2. 2 Press c or d to select cut-off frequency. Each press of c or d selects cut-off frequencies in the following order: 5080125 (Hz) Only frequencies lower than those in the selected range are output from the subwoofer. 3 Press a or b to adjust the output level of the subwoofer. Each press of a or b increases or decreases the level of the subwoofer. +6  6 is displayed as the level is increased or decreased. Using non fading output When the non fading output setting is on, the audio signal does not pass through this units low pass filter (for the subwoofer), but is output through the RCA output. 1 Press AUDIO to select non fading output on/off setting. Press AUDIO until NonFad ON appears in the display. # When the subwoofer controller setting is only PREOUT :FULL, you can switch to the non fading output on/off setting. (Refer to page 33.) 2 Press a to turn non fading output on. NonFad ON appears in the display. Non fading output is now on. # To turn non fading output off, press b. 30 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Adjusting loudness
Loudness compensates for deficiencies in the
low- and high-sound ranges at low volume.
1
Press AUDIO to select Loud.
Press
AUDIO
until
Loud
appears in the dis-
play.
2
Press
a
to turn loudness on.
Loudness level (e.g.,
Loud Mid
) appears in the
display.
3
Press
c
or
d
to select a desired level.
Each press of
c
or
d
selects level in the fol-
lowing order:
Low
(low)
³
Mid
(mid)
³
High
(high)
4
Press
b
to turn loudness off.
Loud OFF
appears in the display.
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off.
1
Press AUDIO to select Sub-W1.
Press
AUDIO
until
Sub-W1
appears in the dis-
play.
#
When the subwoofer controller setting is
PREOUT :FULL
, you cannot select
Sub-W1
.
2
Press
a
to turn subwoofer output on.
Sub-W1 Normal
appears in the display. Sub-
woofer output is now on.
#
To turn subwoofer output off, press
b
.
3
Press
c
or
d
to select the phase of sub-
woofer output.
Press
c
to select reverse phase and
Rev.
ap-
pears in the display. Press
d
to select normal
phase and
Normal
appears in the display.
Adjusting subwoofer settings
When the subwoofer output is on, you can ad-
just the cut-off frequency and the output level
of the subwoofer.
1
Press AUDIO to select Sub-W2.
Press
AUDIO
until
Sub-W2
appears in the dis-
play.
#
When the subwoofer output is on, you can se-
lect
Sub-W2
.
2
Press
c
or
d
to select cut-off frequency.
Each press of
c
or
d
selects cut-off frequen-
cies in the following order:
50
³
80
³
125
(Hz)
Only frequencies lower than those in the se-
lected range are output from the subwoofer.
3
Press
a
or
b
to adjust the output level
of the subwoofer.
Each press of
a
or
b
increases or decreases
the level of the subwoofer.
+6
±
±
6
is displayed
as the level is increased or decreased.
Using non fading output
When the non fading output setting is on, the
audio signal does not pass through this unit
²
s
low pass filter (for the subwoofer), but is out-
put through the RCA output.
1
Press AUDIO to select non fading out-
put on/off setting.
Press
AUDIO
until
NonFad ON
appears in the
display.
#
When the subwoofer controller setting is only
PREOUT :FULL
, you can switch to the non fading
output on/off setting. (Refer to page 33.)
2
Press
a
to turn non fading output on.
NonFad ON
appears in the display. Non fad-
ing output is now on.
#
To turn non fading output off, press
b
.
Audio Adjustments
En
30
Section
07
HHHHHHHHHHHHHH