Pioneer DEH-P9400MP Owner's Manual - Page 62

Understanding built-in CD player error messages Understanding auto-equalizing error messages

Get Pioneer DEH-P9400MP PDF manuals and user guides View all Pioneer DEH-P9400MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Additional Information Understanding built-in CD player error messages When problems occur during CD play, an error message may appear on the display. If an error message appears on the display, refer to the table below to see what the problem is and the suggested method of correcting the problem. If the error cannot be corrected, contact your dealer or your nearest Pioneer service center. Display Cause Remedy ERROR- 11, 12, 17, 30 Dirty disc. Clean disc. ERROR- 11, 12, 17, 30 Scratched disc. Replace disc. ERROR- 22, 23 The CD format cannot be played back. Replace disc. ERROR- 10, 11, 12, 17, 30, 50, A0 Electrical or mechanical problem. Turn the ignition ON and OFF, or switch to a different source, then back to the CD player. ERROR- 44 All tracks are skip tracks. Replace disc. HEAT CD player overheated. Turn off the CD player and wait until the CD player cools down. No audio Nothing has been recorded or the CD format cannot be played back. Replace disc. Understanding auto-equalizing error messages When correct measurement of car interior acoustic characteristics is not possible using the autoequalizer, an error message may appear on the display. If an error message appears on the display, refer to the table below to see what the problem is and the suggested method of correcting the problem. After checking, try again. Display Cause Remedy ERROR CHECK MIC Microphone is not connected. Plug the supplied microphone securely into the jack. ERROR CHECK SPEAKER The microphone cannot pick Confirm that the speakers are up the measuring tone of the connected correctly. front and rear speakers. Correct the input level setting of the power amp connected to the speakers. Set the microphone correctly. ERROR CHECK SYSTEM The surrounding noise level is too high. Stop your car in a place that is as quite as possible, and switch off the engine, air conditioner or heater. Set the microphone correctly. Auto EQ unavailable The operation mode set to NW mode. The auto-equalizing function does not work in NW mode. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
61
Additional Information
U
nderstanding built-in CD player error messages
When problems occur during CD play, an error message may appear on the display. If an error mes-
sage appears on the display, refer to the table below to see what the problem is and the suggested
method of correcting the problem. If the error cannot be corrected, contact your dealer or your near-
est Pioneer service center.
Display
Cause
Remedy
ERROR- 11, 12, 17, 30
Dirty disc.
Clean disc.
ERROR- 11, 12, 17, 30
Scratched disc.
Replace disc.
ERROR- 22, 23
The CD format cannot be
Replace disc.
played back.
ERROR- 10, 11, 12, 17,
Electrical or mechanical
Turn the ignition ON and OFF, or
30, 50, A0
problem.
switch to a different source, then
back to the CD player.
ERROR- 44
All tracks are skip tracks.
Replace disc.
HEAT
CD player overheated.
Turn off the CD player and wait
until the CD player cools down.
No audio
Nothing has been recorded
Replace disc.
or the CD format cannot be
played back.
U
nderstanding auto-equalizing error messages
When correct measurement of car interior acoustic characteristics is not possible using the auto-
equalizer, an error message may appear on the display. If an error message appears on the display,
refer to the table below to see what the problem is and the suggested method of correcting the prob-
lem. After checking, try again.
Display
Cause
Remedy
ERROR CHECK MIC
Microphone is not connected.
Plug the supplied microphone
securely into the jack.
ERROR CHECK SPEAKER
The microphone cannot pick
Confirm that the speakers are
up the measuring tone of the
connected correctly.
front and rear speakers.
Correct the input level setting of the
power amp connected to the
speakers.
Set the microphone correctly.
ERROR CHECK SYSTEM
The surrounding noise level
Stop your car in a place that is as
is too high.
quite as possible, and switch off the
engine, air conditioner or heater.
Set the microphone correctly.
Auto EQ unavailable
The operation mode set
The auto-equalizing function does
to NW mode.
not work in NW mode.