Pioneer DEH-X6800BT Owner's Manual - Page 22
Additional Information - error 10
View all Pioneer DEH-X6800BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Additional Information Troubleshooting The display automatically returns to the normal display. → No operations have been made for about 30 seconds. - Perform an operation. The repeat play range changes unexpectedly. → Depending on the repeat play range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing. - Select the repeat play range again. A subfolder is not played back. → Subfolders cannot be played when [FLD] (folder repeat) is selected. - Select another repeat play range. The sound is intermittent. → You are using a device, such as a cellular phone, that may cause audible interference. - Move electrical devices that may be causing the interference away from the unit. The sound from the Bluetooth audio source is not played back. → There is a call in progress on a Bluetooth-connected cellular phone. - The sound will be played back when the call is terminated. → A Bluetooth-connected cellular phone is currently being operated. - Stop using the cellular phone. → The connection between the unit and the cellular phone is not established correctly after a call made by a Bluetooth-connected cellular phone. 22 En - Make a Bluetooth connection between the unit and the cellular phone again. Error messages Common AMP ERROR → This unit fails to operate or the speaker connection is incorrect. → The protective circuit is activated. - Check the speaker connection. - Turn the ignition switch OFF and back to ON again. If the message remains, contact your dealer or an authorized Pioneer Service Station for assistance. NO XXXX (NO TITLE, for example) → There is no embedded text information. - Switch the display or play another track/file. CD player ERROR-07, 11, 12, 17, 30 → The disc is dirty. - Clean the disc. → The disc is scratched. - Replace the disc. ERROR-07, 10, 11, 12, 15, 17, 30, A0 → There is an electrical or mechanical error. - Turn the ignition switch OFF and back to ON, or switch to a different source, then back to the CD player. ERROR-15 → The inserted disc is blank. - Replace the disc. ERROR-23 → Unsupported CD format. - Replace the disc. FORMAT READ → Sometimes there is a delay between the start of playback and when you start to hear any sound. - Wait until the message disappears and you hear sound. NO AUDIO → The inserted disc does not contain any playable files. - Replace the disc. SKIPPED → The inserted disc contains DRM protected files. - The protected files are skipped. PROTECT → All the files on the inserted disc are embedded with DRM. - Replace the disc. USB device/iPod FORMAT READ → Sometimes there is a delay between the start of playback and when you start to hear any sound. - Wait until the message disappears and you hear sound. NO AUDIO → There are no songs. - Transfer the audio files to the USB device and connect. → The connected USB device has security enabled. - Follow the USB device instructions to disable the security. SKIPPED → The connected USB device contains DRM protected files. - The protected files are skipped. PROTECT → All the files on the connected USB device are embedded with DRM. - Replace the USB device. N/A USB → The connected USB device is not supported by this unit. - Disconnect your device and replace it with a compatible USB device. HUB ERROR → The USB device connected via a USB hub is not supported by this unit. - Connect the USB device directly to this unit using a USB cable. CHECK USB → The USB connector or USB cable has short-circuited. - Check that the USB connector or USB cable is not caught in something or damaged. → The connected USB device consumes more than maximum allowable current. - Disconnect the USB device and do not use it. Turn the ignition switch OFF and back to ACC or ON. Connect only compliant USB devices. → The iPod operates correctly but does not charge. - Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back to ON, or disconnect the iPod and reconnect. ERROR-19 → Communication failed. - Perform one of the following operations, then return to the USB source. • Turn the ignition switch OFF and back to ON. • Disconnect the USB device. • Change to a different source.